Sharp MX-M550U

MX-M700N SIMULATION 7 – 39
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
46-15
Purpose
Adjustment
Function (Purpose)
Used to adjust the print density in the FAX
mode (each super fine mode). (Only when
FAX is installed.)
Section
—
Operation/Procedure
1) Select the number corresponding to one of the following
adjustment items with 10-key. (Select one of 3 - 14.)
* Normal mode (Print density adjustment level)
* Normal mode (Print density adjustment level) (Half-tone
mode)
* Auto mode
* Auto mode (Half-tone mode)
2) Press the [START] key.
3) Enter the print density level with 10-key.
4) Press the [P] or [START] key.
The adjustment value is set.
When [START] key is pressed, printing is performed and the
adjustment value is set simultaneously.
Check the density of print image.
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual paper feed
6 LCC Side LCC
Item
Setting
range
Default
0 TRAY SELECT Paper feed tray
selection
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level
selection
3 AUTO Auto 0 - 99 50
4 1.0 Exposure level 1
5 2.0 Exposure level 2
6 3.0 Exposure level 3
7 4.0 Exposure level 4
8 5.0 Exposure level 5
9 AUTO (H) Auto (Half-tone)
10 1.0 (H) Exposure level 1
(Half-tone)
11 2.0 (H) Exposure level 2
(Half-tone)
12 3.0 (H) Exposure level 3
(Half-tone)
13 4.0 (H) Exposure level 4
(Half-tone)
14 5.0 (H) Exposure level 5
(Half-tone)
1
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE).SELECT 0-14,AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.AUTO 50 4.1.0 50 5.2.0 50
6.3.0 50 7.4.0 50 8.5.0 50
9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50
12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50
Normal display NOW PRINTING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual paper feed
6 LCC Side LCC
1
SIMULATION 46-15
EXP.LEVEL SETUP FAX(SUPER FINE).SELECT 0-14,AND PRESS
START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.AUTO 50 4.1.0 50 5.2.0 50
6.3.0 50 7.4.0 50 8.5.0 50
9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50
12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50