Sharp MX-M550U

MX-M700N SIMULATION 7 – 48
(Copy condition setting in this simulation)
* To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray of the
target paper with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
* The copy magnification ratio can be set with the following
1) Enter 2 with 10-key.
2) Press the [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press the [START] key.
50-2
Purpose
Adjustment
Function (Purpose)
Used to adjust the document scan position,
the image print position, and the void area
(image loss). (Simple adjustment) (This
adjustment is the simple method of SIM 50-
1.) (Document table mode)
Section
—
Operation/Procedure
(Leading edge image loss/void area adjustment)
1) Set the RRCB value of SIM 50-1 to 80 - 99.
2) Set the adjustment values for leading edge image loss adjust-
ment value (LEAD EDGE) and leading edge void adjustment
value (DENA) as follows:
(Standard set value)
Lead edge image loss: 1.5mm (LEDA: 15)/Paper lead edge
void: 3.5mm (DENA: 35)
* Set the adjustment value of LEAD to 15. (Enter 15 as the
adjustment value of LEAD and press [P] key.)
* Set the adjustment value of DENA to 35. (Enter 35 as the
adjustment value of DENA and press [P] key.)
3) Set the adjustment value of L1 to 0. (Enter 0 as the adjustment
value of L1, and press [P] key.)
4) Set the adjustment value of L2 to 0. (Enter 0 as the adjustment
value of L2, and press [P] key.)
5) Make a copy at 400%, and calculate the values of L1 and L2.
(Enter 100 as the set value (MAGNIFICATION) of the copy
magnification ratio, and press [START] key.) (Place a scale on
the document table and make a copy.)
L1 = Distance (mm) from the image lead edge position to the
scale position of 10mm x 10
L2 = Distance (mm) from the image lead edge position to the
paper lead edge x 10
6) Enter the above values as the set values of L1 and L2.
(Enter the adjustment values of L1 and L2, and press [P] key.)
If the adjustment result is not satisfactory, perform the above proce-
dures again from the beginning, or use SIM 50-1 to adjust.
NOTE: If a satisfactory result is not obtained with the above proce-
dures, through the adjustment values are changed individ-
ually, the normal adjustment cannot be made.
Perform procedures 3) to 6) continuously.
(Trailing edge void area adjustment)
Adjust so that the rear edge void area is 3.5mm. (Change the
adjustment value of TRAIL EDGE, and press [START] key.)
(Front/rear frame direction image loss adjustment)
Set the adjustment value of SIDE to 20. (Enter 20 as the adjust-
ment value of SIDE, and press [P] key.)
When this adjustment value is changed, the image position is
shifted in the front/rear frame direction.
(Front/rear frame direction void area)
Adjust so that the total of the front/rear direction void areas is
7.0mm. (Change the adjustment values of FRONT/REAR, and
press [START] key.)
Front frame void area = 3.5mm / Rear frame void area = 3.5mm
If, as shown above, the front and the rear void areas are not even,
use SIM 50-5 to adjust the image off-center position.
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual paper feed
6 LCC Side LCC
Setting range 25 - 400 (%)
2
SIMULATION 50-1
LEAD EDGE ADJUSTMENT. SELECT 0-9, AND PRESS START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 100
(ADJUSTMENT DATA) 3.RRCA 50 4.RRCB 50 10.SIDE2 ADJ. 50
(IMAGE LOSS SETTING) 5.LEAD 15 6.SIDE 20
(VOID SETTING) 7.LEAD_EDGE(DENA) 50
8.TRAIL_EDGE(DENB) 30 9.FRONT/REAR 30
Item
Setting
range
Default
0 TRAY SELECT Paper feed tray
selection
1 - 6 -
1 COPY START Copy START (Default) - -
2 MAGNIFICATION Print magnification
ratio
25 -
400%
400
(Actual measurement value)
3 L1 Distance from the
image lead edge to
the scale of 10mm.
(Platen 400%, 0.1mm
increment)
0 - 999 -
4 L2 Distance from the
paper lead edge to the
image lead edge
(0.1mm increment)
(Image loss set value)
5 LEAD Lead edge image loss
set value
0 - 99 15
6 SIDE Side image loss set
value
20
(Void set value)
7 LEAD_EDGE
(DENA)
Lead edge void set
value
0 - 99 35
8 TRAIL_EDGE
(DENB)
Rear edge void
adjustment value
9 FRONT/REAR Front/Rear void
adjustment value
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.