Sharp PN-B501 - Specifications

45
E
Specications
n
Product Specications
Model PN-B501 PN-B401
LCD component
50" Class
[49-1/2 inch (125.73 cm) diagonal]
TFT LCD
40" Class
[39-1/2 inch (100.33 cm) diagonal]
TFT LCD
Max. resolution (pixels)
1920 x 1080
Max. colors
Approx. 16.77 million colors
Pixel pitch
0.5709 mm (H) × 0.5708 mm (V) 0.45735 mm (H) × 0.4494 mm (V)
Brightness (typical) 300 cd/m
2
*
1
Contrast ratio (typical) 5000: 1
Viewing angle
178° right/left/up/down (contrast ratio ≥ 10)
Screen active area inch (mm)
43-1/8 (W) x 24-1/4 (H)
(1095.84 x 616.41)
34-9/16 (W) x 19-1/8 (H)
(878.112 x 485.352)
Computer input signal
Analog RGB (0.7 Vp-p) [75 Ω], HDMI
Sync signal
Horizontal/vertical separate (TTL: positive/negative)
Plug and play
VESA DDC2B
Power management
VESA DPMS
Input terminals
Video Mini D-sub 15 pin, 3 rows x 1
HDMI x 2
DisplayPort x 1
Serial (RS-232C)
D-sub 9 pin x 1
Audio
3.5 mm mini stereo jack x 1
Output terminals
Video DisplayPort x 1
Serial (RS-232C)
D-sub 9 pin x 1
Audio
3.5 mm mini stereo jack x 1
Android OS Android 4.4.2
CPU Quad-Core (ARM Cortex-A17 processor)
Memory 2GB
Storage 8GB
SD card slot SD/SDHC x 1
USB port USB (USB 2.0 compliant) x 3
LAN terminal 10 BASE-T/100 BASE-TX/1000 BASE-T
Expansion slot 12 V, 2.5 A
(power supplied when expanding the functions with an optional part)
Speaker output 7 W + 7 W
Power requirement AC 100 - 240 V, 1.4 A, 50/60 Hz AC 100 - 240 V, 1.1 A, 50/60 Hz
Operating temperature
*
2
32°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption
(input signal waiting mode / standby mode
*
3
)
120 W (19 W / 12 W) 92 W (19 W / 12 W)
Dimensions (excluding protrusions) inch (mm)
Approx. 44-3/16 (W) x 2-11/16 (D) x
25-1/2 (H) (1123 x 68 x 647)
Approx. 35-1/2 (W) x 2-5/8 (D) x
20-3/16 (H) (902 x 67 x 513)
Weight lbs. (kg)
Approx. 49 (22) Approx. 34 (15)
*1 Brightness will depend on input mode and other picture settings. Brightness level will decrease over time. Due to the nature of the
equipment, it is not possible to precisely maintain a constant level of brightness.
*2 When using this monitor laying at on a surface (when the monitor is tilted more than 20 degrees upward or downward from the
perpendicular in relation to a level surface), use this monitor at a temperature between 32°F (0°C) to 86°F (30°C).
Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specied by the optional equipments.
*3 When POWER SAVE MODE is set to OFF, and no optional part is attached. When POWER SAVE MODE is set to ON: 0.5 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement
without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from
these values in individual units.