Sharp R-961 (W) - Page 34

COMPONENT
REPLACEMENT
AND
ADJUSTMENT
PROCEDURE
CONVECTION
MOTOR
16.Remove
the
pipe,
the
auxiliary
fan
and
one
(1)
washer
13.
Remove
the
one
(1)
nut,
spring
washer
and
plate
washer
from
the
convection
motor
shaft.
holding
the
convection
fan
to
the
convection motor
shaft.
17.Remove
the
two
(2)
screws
holding
the
convection motor
14.
Remove
the
convection
fan
from
the
convection
motor
shaft.
to
the
convection
motor
angle.
15.
Remove
the
two
(2)
screws
holding
the
convection
motor
18.
Pull
out
one
(1)
pin
from
the
convection
motor
shaft.
angle to
the
convection
duct
through
the
rear
heat
cover.
19.
Now, the
convection
motor
is
free.
GRILL HEATING ELEMENT ASSEMBLY REMOVAL
4.
CARRY
OUT
3D
CHECKS.
assembly
and
the
sensor
cover
to
the
exhaust
duct.
2.
Disconnect
the
wire
leads
from
the grillheatingelements
|
6.
Removethe
exhaust
duct
assembly
from
the
oven
cavity.
and
the
thermal
cut-out (GRILL).
7. Push the
two
tabs
holding
the
grill
heating
element
3.
Remove the
two
(2)
screws
holding
the
exhaust
duct
assembly
to the
oven
cavity.
assembly
to
the
oven
cavity.
8.
Release
the
grill
heating
element
assembly
from
the
4.
Remove
the
three
(3) screws
holding
the
damper
duct
to
oven
cavity by
sliding
the
cover.
the
oven cavity.
9.
Now
the
grill heating element
assembly
is free.
5. Remove the one (1) screws holding the AH sensor
DAMPER MOTOR REMOVAL
1. CARRY OUT 3D CHECKS. 4. Release the one (1) tab of the damper motor from the slit
2. Disconnect the wire leads from the damper motor. of the damper motor angle.
3. Remove the one (1) screw holding the damper motor to 5. Now, the damper motor is free.
the damper motor angle.
ROTISSERIE MOTOR REPLACEMENT
REMOVAL 6. Now, the rotisserie motor is free. And alsothe rotisserie
1. CARRY OUT 3D CHECKS. bearing and rotisserie coupling are free.
2. Disconnect the wire leads from the rotisserie motor. INSTALLATION
3. Remove the two (2) screws holding the rotisserie motor 1. Install the rotisserie motor to the rotisserie motor angle
angle to the oven cavity. with two (2) screws.
4. Remove the rotisserie motor angle with the rotisserie 2. Install the rotisserie bearing to the oven cavity.
motor. : 3. Install the rotisserie coupling to the rotisserie motor shaft.
5. Remove the two (2) screws holding the rotisserie motor 4. Install the rotisserie motor angle with the rotisserie motor
to the rotisserie motor angle. and the coupling to the oven cavity with two (2) screws.
TURNTABLE MOTOR REMOVAL
_
. Disconnect the oven from power supply.
2. Remove the one (1) screw holding the turntable motor
cover to the base plate.
3. Disconnect the wire leads from the turntable motor. O-ring
4. Remove the two (2) screws holding the turntable motor to
Coupling
the
thermal
cover
bottom.
ae
Sai
5.
Now,
the
turntable
motor
is
free.
:
NOTE:
When
the
coupling
or
O-ring
is
replaced
with
a
new
one,
the
grease
(Shinetsu
Silicone
grease
G420
of
Shinetsu
Chemical
Co.
Ltd.)
must
be
applied
as
shown
Figure
C-5.
If the
grease
is
not
applied,
the
coupling
and
O-ring
may
be
damaged.
Figure
C-5.
Grease
applying
position.
R-961 - 32