Sharp SMD2470ASY - User Manual

1
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES ANd dImENSIoNS
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated
clearances and dimensions on pages 2 - 5. See Figure 1 (for 24") or Figures 4 and 5 (for 30").
Microwave Drawer : SMD2470AS, SMD3070AS
InstallatIon Manual
UNPACkING yoUR mICRoWAvE dRAWER
 Remove all packing
materials from inside
the Microwave Drawer.
DO NOT REMOVE
THE WAVEGUIDE
COVER, which is
located on the top
of the Microwave
Drawer.
 Remove the feature
sticker, if there is one.
Check the drawer for
any damage, such as
misaligned or bent
drawer, damaged drawer seals and sealing surfaces, broken
or loose Microwave Drawer guides and dents inside the cavity
or on the front side of the drawer. If there is any damage, do
not operate the Microwave Drawer and contact your dealer or
a SHARP AUTHORIZED SERVICER.
ImPoRtANt NotES to thE INStALLER
 Read all of the Installation Manual before installing the
Microwave Drawer.
  Remove all packing material before connecting the electrical
supply.
  Observe all governing codes and ordinances.
  Be sure to leave these instructions with the consumer.
ImPoRtANt NotES to thE CoNSUmER
Keep this manual with your Operation Manual for future
reference.
 As when using any microwave oven generating heat, there
are certain safety precautions you should follow. These are
listed in the Operation Manual. Read all and follow carefully.
 Be sure your Microwave Drawer is installed and grounded
properly by a qualied installer or service technician.
ImPoRtANt SAfEty INStRUCtIoNS
If the information in this manual is not followed
exactly, a re or electrical shock may result that could cause
property damage, personal injury or death.
To reduce the risk of tipping, the Microwave
Drawer must be secured by a properly installed Anti-Tip
block.
 This Microwave Drawer must be electrically grounded in
accordance with local codes.
 Make sure the wall coverings and the cabinets around the
Microwave Drawer can withstand the heat generated by the
Microwave Drawer.
Never leave children alone or unattended in
the area where a Microwave Drawer is in use. Never leave the
drawer open when the microwave is unattended.
Stepping, leaning or sitting on the drawer may
result in serious injuries and can also cause damage to the
Microwave Drawer.
 Do not use the Microwave Drawer as a storage space.
This creates a potentially hazardous situation.
 Check that the time-of-day is in the display. If not, touch
STOP/CLEAR to prevent unintended use.
1
Mounting
flange
Waveguide
cover
Sealing
surface
Oven
cavity
Sealing
surface

Summary

Special Warning

Important Safety Instructions

Clearances and Dimensions

24 Microwave Drawer Measurements

Detailed measurements and diagrams for the 24-inch microwave drawer installation, including cutout dimensions and clearances.

30 Microwave Drawer Measurements

Anti-Tip Block Installation

Electrical Outlet and Grounding

Drawer Installation Steps

Overview

1. Function Description
2. Usage Features
3. Maintenance Features

This document provides installation, safety, and operational guidelines for the Sharp Microwave Drawer models SMD2470AS and SMD3070AS. It is designed for both qualified installers and consumers, emphasizing proper setup, safe usage, and basic maintenance to ensure optimal performance and longevity of the appliance.

Function Description

The Sharp Microwave Drawer is a sophisticated kitchen appliance designed to integrate seamlessly into cabinetry or under a wall oven, offering convenient microwave cooking functionality. Unlike traditional microwave ovens, this model features a drawer-style opening, allowing for easy loading and unloading of food items from above. This design is particularly beneficial for accessibility, as it can be installed at various heights to suit user preferences and kitchen layouts, including under countertops or within wall cabinets. The microwave drawer utilizes microwave energy to rapidly heat and cook food, providing a versatile solution for reheating leftovers, defrosting ingredients, and preparing a wide range of meals. Its intuitive controls, typically located on a hidden panel that becomes accessible when the drawer is open, allow users to select various cooking modes and power levels. The appliance is engineered to accommodate common kitchenware, such as 9" x 13" oblong dishes and bags of microwave popcorn, making it suitable for everyday cooking tasks. The drawer's smooth operation and robust construction contribute to a premium user experience, blending advanced technology with practical design for modern kitchens.

Usage Features

The Microwave Drawer is designed with user convenience and safety in mind. Its drawer-style operation eliminates the need to reach over hot dishes, a common issue with traditional over-the-range or countertop microwaves. To use the drawer, users simply open it, place food inside, and then close it before selecting cooking settings. The control panel is typically hidden when the drawer is closed, contributing to a sleek, integrated look in the kitchen. When the drawer is opened, the control panel becomes accessible, allowing for easy selection of cooking times, power levels, and specialized functions.

Key usage features include:

• Drawer-Style Access: The primary feature is the pull-out drawer, which allows for effortless loading and unloading of food from a comfortable height, reducing strain and improving safety, especially when handling hot items.
• Integrated Design: The appliance is built for flush installation into cabinetry or under a wall oven, providing a clean, custom look that complements contemporary kitchen aesthetics. This integration helps save counter space and creates a streamlined appearance.
• Accommodates Various Dish Sizes: The interior cavity is spacious enough to fit standard cookware, such as a 9" x 13" oblong dish, making it suitable for a variety of cooking and reheating needs. It also comfortably fits a bag of microwave popcorn, indicating its capacity for common microwaveable items.
• Anti-Tip Block: For safety, the microwave drawer must be secured with an anti-tip block during installation. This critical feature prevents the appliance from tipping forward, especially when the drawer is fully extended or if weight is inadvertently placed on it, thereby reducing the risk of injury from spilled hot liquids or the drawer itself.
• Electrical Requirements: The appliance operates on a standard 120-volt, 60 Hz, 15-amp electrical supply. It is equipped with a 3-prong grounding plug and requires a properly installed and grounded wall receptacle. This ensures safe electrical operation and minimizes the risk of electrical shock.
• Control Panel Accessibility: The control panel is strategically placed to be visible and accessible when the drawer is open, allowing users to easily program cooking settings. When the drawer is closed, the panel is concealed, maintaining the appliance's minimalist design.
• Safety Precautions: The manual emphasizes several safety precautions, such as never leaving children unattended near the drawer, avoiding stepping or leaning on it, and not using it as a storage space. These guidelines are crucial for preventing accidents and damage to the appliance.
• Unintended Use Prevention: Users are advised to ensure the time-of-day is displayed on the control panel. If not, touching "STOP/CLEAR" is recommended to prevent unintended operation, highlighting a feature designed to enhance safety.

Maintenance Features

Maintaining the Sharp Microwave Drawer involves simple, routine care to ensure its longevity and hygienic operation. The manual directs users to the separate Operation Manual for detailed cleaning instructions, but general principles of microwave maintenance apply.

Key maintenance features and considerations include:

• Waveguide Cover: The manual explicitly states, "DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the top of the Microwave Drawer." This cover protects the waveguide, a crucial component that directs microwave energy into the oven cavity. Keeping it intact is essential for the microwave's proper functioning and safety. Any damage to this cover could impair performance and potentially expose users to microwave energy.
• Oven Cavity Cleaning: Regular cleaning of the oven cavity is necessary to prevent food splatters and residue from building up. Food particles can absorb microwave energy, leading to uneven cooking or potential arcing. A damp cloth and mild detergent are typically sufficient for cleaning the interior surfaces.
• Drawer Seals and Sealing Surfaces: The integrity of the drawer seals and sealing surfaces is vital for preventing microwave energy leakage. Users are advised to inspect these areas for damage during unpacking and periodically thereafter. Any damage, such as misalignment or tears, should be addressed by a qualified service technician to ensure safe operation.
• Exterior Cleaning: The exterior surfaces, including the mounting flange and control panel, can be wiped clean with a soft, damp cloth. Avoiding abrasive cleaners or harsh chemicals will help preserve the finish of the appliance.
• Damage Inspection: Upon unpacking, users should check for any physical damage, such as a misaligned or bent drawer, damaged drawer seals, broken or loose drawer guides, or dents inside the cavity or on the front. If any damage is found, the appliance should not be operated, and the dealer or a Sharp Authorized Servicer should be contacted immediately. This proactive inspection helps prevent potential safety hazards and ensures the appliance is in optimal condition from the start.
• Professional Servicing: For any issues beyond routine cleaning or minor troubleshooting, the manual emphasizes that "INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER." This ensures that complex repairs or adjustments are handled by professionals who understand the appliance's intricate components and safety requirements.
• Model and Serial Number Location: The nameplate, containing the model and serial number, is located beyond the back wall of the microwave cavity, accessible when the drawer is fully open. This information is crucial for service inquiries and ordering parts.
• Pre-Service Checks: The manual encourages users to consult the "BEFORE YOU CALL FOR SERVICE" section in the Operation Manual. This section typically lists common occurrences that are not indicative of a defect, potentially saving time and expense by allowing users to resolve minor issues themselves before contacting service.

By adhering to these usage and maintenance guidelines, users can ensure the safe, efficient, and long-lasting performance of their Sharp Microwave Drawer.

Sharp SMD2470ASY Specifications