Sharp XL-HF102B User Manual

E-7
Remote control
General control
■ Battery installation
Use 1 “AA” size battery (UM/SUM-3, R6, HP-7 or similar).
Battery is not included.
1 Open the battery cover.
2 Insert the battery according to the terminal indicated in
the battery compartment. When inserting or removing
the battery, push it toward the (–) battery terminals.
3 Close the cover.
Caution:
● Remove the battery if the unit will not be used for a
long period of time. This will prevent potential damage
due to battery leakage.
● Do not use rechargeable battery (nickel-cadmium bat-
tery, etc.).
● Installing the battery incorrectly may cause the unit to
malfunction.
● Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat such as sunshine, re
or the like.
Notes concerning use:
● Replace the battery if the operating distance is reduced
or if the operation becomes erratic.
● Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
● Exposing the sensor on the unit to strong light may
interfere with operation. Change the lighting or the di-
rection of the unit if this occurs.
● Keep the remote control away from moisture, heat,
shock and vibrations.
■ Test of the remote control
The remote control can be used within the range shown below:
Remote sensor
8” - 20’
(0.2 m - 6 m)
■ To turn the power on
Press the ON/STANDBY button to turn the power on or off.
■ Display brightness control
Press the DIMMER button (remote control).
Dimmer 1
Dimmer 2
Dimmer off
(Display is dim).
(Display is bright).
(Display gets dimmer).
■ Volume auto fade-in
If you turn off and on the main unit with the volume set to
27 or higher, the volume starts at 16 and fades in to the
last set level.
■ Volume control
Turn the volume knob toward VOLUME +/– (main unit) or
press VOL +/– (remote control) to increase or decrease
the volume.
■ Muting
To mute the volume, press the button (remote control).
Press again to restore the volume.
■ Direct key power on function
When you press any of the following buttons, the unit turns
on.
● CD / , USB / , BLUETOOTH / , AUDIO/LINE
(INPUT), TUNER (BAND), OPEN/CLOSE (remote
control): Selected function is activated.
● / (main unit): The unit turns on and playback of the last
function will start (CD, USB, BLUETOOTH, AUDIO IN,
LINE IN, TUNER)
■ Auto power off function
The main unit will enter the standby mode after 15 minutes
of inactivity during:
Audio/Line In: No detection of input signal.
CD: In the stop mode or no disc.
USB: In the stop mode or no media.
Bluetooth: In the pause mode or not connected condition.
■ X-Bass control
When the power is rst turned on, the unit is in the extra
bass mode. “X-BASS” indicator appears. To cancel this
mode, press the X-BASS button (remote control).
■ Bass or Treble control
1 Press the BASS or TREBLE button to select “Bass” or “Tre-
ble” respectively.
2 Within 5 seconds, press the VOL (+ or –) button to adjust the
bass or treble.
- 5 ↔ - 4
........
↔ + 4 ↔ + 5
- 5 ↔ - 4
........
↔ + 4 ↔ + 5
■ Function
Press the FUNCTION button repeatedly to select desired
function.
CD FM MONOFM STEREO
USB
Line In
Audio In
Bluetooth
AM
Note:
The backup function will protect the memorized function
mode for a few hours should there be a power failure or
the AC power cord becomes disconnected.

Sharp XL-HF102B Specifications

General

Brand	Sharp
Model	XL-HF102B
Category	Stereo Receiver
Language	English