Shihlin electric SS2-043-2.2K - User Manual

Safety Instructions
Safety Instructions
When using Shihlin inverters, please follow the installation to ensure the safety of user and others.
The following instructions will be classified and described by icons：
DANGER It means dangerous instructions, and incorrect handling may result in death or
severe injury.
CAUTION It means caution instructions. Incorrect handling may result in injury or property
damage.
It means caution and execution need to be done. Please operate according to the
instructions.
DANGER
 Inverters must be used on the location except corrosive gas, water, flammable gas.
 Please operate far from flammable substance or explosives.
 Please do not lay the inverter on an intense trembling or shaking occasion.
 Do not operate wires soaked under oil or water.
 Prohibit touching any part in the inverter when power is ON to avoid electric shock.
 Three-phase power cannot be connected to terminal U/T1, V/T2, W/T3.
 The terminal of the inverter must be correctly grounded.
 Do not conduct wiring when the power is ON.
CAUTION
 Do not conduct hi-pot test on internal components of the inverter, for semiconductor
is easily damaged by high voltage.
 There are CMOS IC components on PCBAs which are especially sensitive to static
electricity. Please do not touch PCBAs before taking anti-static measures.
 Even if the motor stops, a charge may still remain in the main circuit terminals of
the inverter with hazardous voltages.
 Only qualified persons are allowed to install, wire and maintain the inverter.
 After some functions are set, the motor may start immediately once power is ON.
 Please choose the safe area to install the inverter, avoiding heat, direct sunlight,
moisture humidity and splashing of droplets.
 When wiring between the inverter and motor is too long, it may damage the layer
insulation of the motor. A reactor can be mounted between inverter and motor,
avoiding insulation is damaged.
 For the installation power system of rated voltage, it cannot be over 240V for 220
series; it cannot be over 480V for 440 series.
 Only qualified personnel familiar with wiring is allowed to perform wiring.
 For the installation direction and method, please refer to the regulations.
 Make sure to use the temperature in a safe range.
 Please follow the installation to use the voltage.
 When there are problems in operation, please first unload the motor, after zero-load
operation is OK, and then connect to the machine.
 Please confirm whether the inverter power is in line with the motor power.
 Before running, please confirm whether the emergency switch can operate normally.
 Power wire, U, V, W wires and signal wire should not be stranded, but separately.
 Please turn off the power if it is not used for a long time.

Summary

Safety Instructions

DANGER

Instructions indicating dangerous situations that may result in death or severe injury.

CAUTION

Instructions indicating cautions to prevent injury or property damage if mishandled.

3. Introduction of Shihlin Inverter

3.5 Installation and Wiring

Guidelines for transporting, storing, installing, and wiring the inverter.

4. Primary Operation

4.1 Operation Modes of the Inverter

Description of the inverter's nine operation modes and the panel's five working modes.

4.2 Basic Operation Procedures for Different Modes

Step-by-step procedures for operating the inverter in various modes.

4.3 Operation

5. Parameter Description

5.5 Acceleration;Deceleration Time (P.7, P.8, P.20, P.21, P.44, P.45)

5.16 Communication Function (P.32, P.33,P.34, P.36, P.48~P.53, P.153~P.154)

Configures communication parameters like baud rate, protocol, and error handling.

5.21 Multi-function Output (P.40, P.64, P.74, P.85, P.120 and P.187)

5.53 PID Control (P.170~P.183, P.223~P.225)

Sets up PID control loops for precise process regulation.

5.66 Commercial Power Supply Frequency Operation Function (P.247~P.250)

5.70 Alarm History Parameters (P.288~P.291)

Stores and displays past alarm codes, status, and messages.

5.79 Inverter Reset (P.997)

Resets the inverter to its default operational state.

5.80 Restoration of the Parameters to the Default Values (P.998 and P.999)

Restores all or selected parameters to their factory default settings.

6. Inspection and Maintenance

6.1 Daily Inspection

6.2 Periodical Inspection (During Stop)

Appendix 2 Alarm Code List

Appendix 3 Warning Code List

Appendix 4 Troubles and Solutions

Appendix 5 Optional Equipment

1. DU06 operation panel

Appendix 6 European Specification Compatibility Description

1. Electromagnetic compatibility command (EMC):

2. Low-voltage command (LVD):

Shihlin electric SS2-043-2.2K Specifications

General

Model	SS2-043-2.2K
Category	Inverter
Brand	Shihlin Electric
Rated Output Power	2.2 kW
Operating Temperature	-10°C to +50°C
Enclosure Rating	IP20
Input Voltage	3-Phase 380~480VAC
Control Method	V/F control, sensorless vector control
Overload Capacity	150% for 60 seconds
Efficiency	98% (typical)
Protection Features	Over-voltage, Under-voltage, Over-current, Overload, Short circuit, Overheat
Ambient Humidity	5% to 95% RH, non-condensing
Altitude	Below 1000m without derating
Communication Interface	RS-485 (Modbus RTU)
Cooling Method	Forced air cooling