-1-
安全上的注意事項：
使用本機前請詳細閱讀本說明書及所搭配之
馬達說明書，配合正確使用，並須由受過正
確訓練之人員來安裝或操作。
1-1 作業環境的安全
(1) 電源電壓：
電源電壓請遵照馬達與控制箱 牌
所標示之規格±10%範圍內操作。
(2) 電磁波干擾：
請遠離高週磁波器或電波發射器等，
以免產生的電磁波干擾本驅 裝置，
因而發生錯誤 作。
(3) 溫濕度
1﹒請不要在室溫45度C以上或5度C以下
的場所操作。
2﹒請不要在日光直接照射的場所或室外
運作。
3﹒請不要在暖氣(電熱器)旁運作。
SAFETY PRECAUTION :
Please read this manual carefully,
also wit h related m an ua l fo r the
machine head before use﹒ For perfect
operation and safety,installing and
operating this product by trained
personal is required﹒ When install and
op e r ate H V P-70 M INI S E RVO M O TOR,
p r e c a u t i o n m u s t b e t a k e n a s t h e
following﹒ This product is designed
for specify sewing machine and must
not be used for other purposes﹒
1.1 Work Environment :
(1) Power voltage :
Only use Power Voltage indicated
on the name plate of the HVP-70 +
10% ranges﹒
(2)
Electromagnetic pulse interference :
To avoid the false operate, please
keep the product away from the
high electromagnetic
machinery or electro generator﹒
(3) Temperature :
a﹒
Please don't operate in room tempe-
rature is above 45 C or under 5 C
b﹒Avoid operating in direct sun
light or outdoors area﹒
c﹒Avoid operating near the heater﹒
-2-
4﹒請不要在相對濕度30%以下或95%以
上或有露水的場所運作。
1-2 安裝的安全
(1)
機器、馬達、控制箱：請遵照說明
書正確裝好。
(2) 電源線：
1﹒請注意不要被外物壓住或過度扭曲
電源線
2﹒裝釘電源線時請不要靠近會轉 的
手輪、皮帶輪及三角皮帶，最少要
離開3∼5公分以上。
(3) 接地：
1﹒
為防止雜訊干擾或漏電事故，請做
好
接地工程。
2﹒電源線的接地線須以適當大小的導
線和接頭連接到生產工廠的系統地
線，此連接必須被永久固定。
d﹒Avoid operating in the area
which humidity is 30% or less
and 95% or more, also stay away
from dew area﹒
(4) Atmosphere :
a﹒
Avoid operating in dusty area,
and
stay away from corrosive material﹒
b﹒
Avoid operating in evaporate
or
combustible gas area﹒
1.2 Safety In Installation :
(1) Motor and control box :
Follow the instruction in this
manual for correct installation﹒
(2) Power cord :
a﹒Avoid power cord being applied
by heavy objects of excessive
force, or over bend﹒
b﹒Power cord must not set to be
near the handwheel, keep 3mm
spare or above﹒
c﹒
Check the outlets voltage before
plugging the cord, make sure it
match the voltage shown on the
name plate of the HVP-70 in + 10%
ranges﹒
(3) Grounding :
a﹒
To avoid the static interference
and current leakage, all ground
ing
must done﹒
b﹒Use the correct connector and
extension wire when connecting
ground wire to Earth and secure
it tightly﹒
To Next Page
Loading...
