Shinko Denshi HTR-80CE User Manual

82 pages

To Next Page

270011M21

T u n i n g F o r k A n a l y t i c a l B a l a n c e

ＨＴ/ＨＴＲ-ＣＥ

Series

Operation Manual

SHINKO DENSHI CO., LTD.

IMPORTANT

 To ensure safe and proper use of the balance, please read this

manual carefully.

 After reading this manual, store it in a safe place near the balance, so

you can review it as needed.

Default Chapter3
- Table of Contents3
- Contents3
1 Precautions Relating to Use5
2 Names of Component Parts9
- Main Unit9
- Operation Keys10
- Displayed Signs11
3 Installation of the Balance12
4 Basic Operation13
- Power On/Off13
- Weighing13
- Zero Adjustment13
- Tare (Pan)13
- Set a Gross Weight14
- Single-Touch Response Setting14
- Data Output15
- Hanging Measurement15
5 Function 117
- Setting and Check17
- Description of Function 118
- Specific Gravity Setting21
- Limit/Addition Functions21
- Interface22
6 Function 223
- Calling and Setting23
- Description of Function 223
7 Weighing and Measurement Modes24
- Weighing and Measurement24
- Weighing Machine24
8 Parts Counting25
9 Percentage Weighing27
- Set a Reference Weight by Weighing an Actual Sample27
- Set a Reference Weight by Entering a Value28
10 Unit Converting29
11 Gravimeter30
- Measurement Procedures for Specific Gravity30
- Entering Water Temperature or the Specific Gravity of the Media32
12 Addition Function34
- Cumulate Function34
- Net Addition Function35
13 Limit Function37
- Setting the Limit Function37
- Judgment and Saving37
- Display of Judgment Results37
- Judge by Absolute Values38
- Judge by Deviation Values41
- Bar Graph for the 2-Point Scale45
14 Calibration and Span Test for the Balance46
- Span Adjustment with Built-In Weights46
- Span Adjustment with External Weight46
- Span Test with Built-In Weights47
- Span Test with External Weight47
- Calibration of Built-In Weights47
- Entry of Weight Error49
- Advice CAL and Full-Automatic Span Adjustment50
- Auto Repeatability Measurement (ARM)50
15 Date and Time Setup51
- Time Setup51
- Date Setup51
16 Various Functions52
- Auto Backlight off52
- Set Unit52
- Date Display52
- Time Stamp Output52
- Direct Start52
- Interval Output Function53
- Input of ID no54
17 Input/Output Functions55
- RS232C Output55
- Output to Peripherals58
- Type of Communication Texts59
- Output Data59
- Input Commands63
- Special Format Output69
18 Use Printers71
- Setting up the Printer71
- Outputting Calibration Results71
- Output of Measurement Data in Compliance with ISO/GLP/GMP71
19 Output in Compliance with ISO/GLP/GMP72
20 Removing the Windshield Door75
- Caring for the Balance75
21 Troubleshooting76
22 Specifications77
- Basic Specifications77
- Weighing Capacity and Minimum Readability by Unit78
23 Unit Conversion Table79

Questions and Answers:

M
Mary BurkeAug 10, 2025
Why does the weight indication contain an error on my Shinko Denshi Scales?
- T
  Tammy LopezAug 10, 2025
  If the weight indication contains an error on your Shinko Denshi Scales, there might be a few reasons. First, if the scales haven't been used for a while or have been moved, perform a span adjustment. Second, ensure the adjusters are settled and the scale is horizontal. Refer to page 10 for instructions. Lastly, verify that the tare weight is correctly set.
C
Christopher BakerAug 15, 2025
How to fix no display on Shinko Denshi Scales?
- E
  Edward MccarthyAug 15, 2025
  If there is no display on your Shinko Denshi Scales, ensure that the AC adapter is properly connected.