13
AS200-AS200A-AS300 / IRL / A31008-M2208-V101-1-7619 / main.fm / 02.11.2010
Appendix
Entering letters/characters
Press the relevant key the number of times indicated.
Briefly press the hash key # to switch from "Abc" to
"123" mode, from "123" to "abc" mode and from "abc"
to "Abc" mode.
Standard characters
1) Space
Specifications
Recommended batteries
Technology: Nickel-metal-hydride (NiMH)
Size: AAA (Micro, HR03)
Voltage: 1.2 V
Capacity: 400–800 mAh
We recommend the following types of battery:
◆ GP 550/700 mAh
◆ Yuasa Phone 700/800 mAh
◆ Peacebay 550/650 mAh
(Valid at the time of going to press)
The handset is supplied with recommended batter-
ies.
Base station power consumption
General specifications
Questions and answers
If you have any queries about the use of your
telephone, visit our website at
www.gigaset.com/service
for 24-hour support. The table below contains a list of
common problems and possible solutions.
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x11x12x13x14x
1
1 £ $ ¥ ¤
2
a b c 2 ä á à â ã ç
I
d e f 3 ë é è ê
4
g h i 4 ï í ì î
5
j k l 5
L
m n o 6 ö ñ ó ò ô õ
M
p q r s 7 ß
N
t u v 8 ü ú ù û
O
w x y z 9 ÿ ý æ ø å
Q
. , ? ! 0 + - : ¿ ¡ " ’ ; _
P
* / ( ) < = > %
#
Abc
-->
123
123
-->
abc
# @ \ & §
In standby mode
– Handset in base station
– Handset outside base station
approx. 1.3 W
approx. 1.3 W
During a call approx. 1.5 W
DECT standard is supported
GAP standard is supported
Range up to 300 m outdoors
up to 50 m indoors
Base station power supply 230 V ~/50 Hz
Environmental conditions
in
operation
+5°C to +45°C, 20% to
75%
relative humidity
Problem Cause Solution
Nothing
appears in the
display.
The handset is not
switched on.
The batteries are
flat.
Press the end call
key a for approx.
5
seconds or place the
handset in the base
station.
Charge or replace the
batteries.
No wireless
connection to
the base sta
-
tion, Base
flashes in the
display.
The handset is out-
side the range of
the base station.
The handset is not
registered.
The base station is
not turned on.
Move the handset
closer to the base
station.
Register the handset
¢ page 10.
Check the mains
connector on the base
station
¢ page 3.
You cannot
hear a ringer/
dialling tone
from the fixed
line network.
The phone cord
supplied has not
been used or has
been replaced by a
new cord with the
wrong jack con
-
nections.
Please always use the
phone cord supplied or
ensure that the
pin
connections are
correct when purchas
-
ing from a retailer:
3-4 assignment of
telephone leads/EURO
CTR37.
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
You have entered
the wrong
system
PIN.
Reset the system PIN to
the default 0000
¢ page 12.
All handsets are de-
registered. All settings
are reset. All lists are
deleted.
To Next Page
Loading...
