9001670791 (010707) SE23HI60AG
*9001670791*
Quick reference guide Dishwasher
en
Before using forthefirst time, read theoperating instructions.
Short and handy...
... everything your dishwasher needs.
Overview of water hardness settings
You can find an overview of the
water hardness values that can
be selected here.
A table of country-specific units
can be found in the instruction
manual.
Hardness
range
mmol/l Setting
value
Soft 0 - 1.1 H00
Soft 1.2 - 1.4 H01
Medium 1.5 - 1.8 H02
Medium 1.9 - 2.1 H03
Medium 2.2 - 2.9 H04
Hard 3.0 - 3.7 H05
Hard 3.8 - 5.4 H06
Hard 5.5 - 8.9 H07
Setting the water softening sys-
tem
1.
Press .
2.
To open the basic settings, press
for 3 seconds.
a The display shows Hxx.
a The display shows .
3.
Press repeatedly until the right
water hardness has been set.
4.
To save the settings, press
for 3 seconds.
Adding special salt
To avoid damage to the appliance, only add special
salt to the dispenser for special salt just before the
programme starts.
1.
Unscrew the lid of the dispenser for special salt
and remove.
2.
On initial start-up: Fill the dispenser right up with
water.
3.
Add the special salt to the
dispenser. The water in the
dispenser is displaced and
forced out. Never add de-
tergent.
4.
Place the lid back on the dispenser and turn to
close.
Adding rinse aid
1.
Press the catch on the lid
of the dispenser for rinse
aid and lift .
2.
Add rinse aid up to the
max mark.
3.
Close the lid of the dispenser for rinse aid.
a The lid clicks into position.
How to use your appliance
1.
Load the tableware.
Only clean tableware that is suitable for dish-
washers. Remove large remnants of food from
the tableware. Check that the spray arms can ro-
tate freely.
2.
Add detergent.
3.
Switch on the appliance .
4.
Select the programme.
5.
Start the programme .
6.
Remove the tableware at the end of the pro-
gramme.
7.
To cancel the programme, press for
approx. 4seconds.
The programme is cancelled and ends after ap-
prox. 1minute.
Programmes
The programme data has been meas-
ured in the laboratory according to
European standard EN60436.
The consumption figures depend on
the programme and additional func-
tion selected.
The runtime will change if the rinse
aid system is switched off or rinse aid
needs to be added.
Programme 1) Duration [h:min]
2) Energy [kWh]
3) Water [l]
Intensive 70°
1) 2:05 -2:15
2) 1,300 -1,400
3) 11,5 -14,0
Auto 45-65°
1) 1:40-2:45
2) 0,900-1,500
3) 7,0-15,5
Eco 50°
1) 4:55
2) 0,836
3) 9,5
Speed 65°
1) 1:00
2) 1,300
3) 10,5
Speed 45°
1) 0:29
1
2) 0,800
3) 10,5
Machine Care
1) 2:10
2) 1,350
3) 15,2
Favourite
1) 0:15-0:15
2) 0,050-0,050
3) 4,0-4,0
1
half standard load
Adding detergent
1.
Add the detergent to the
dry detergent dispenser.
2.
Close the lid of the deter-
gent dispenser.
a The lid clicks into position.
To Next Page
Need help?
General
