Siemens IQ300 SN63HX52CG User Manual

9001643835 (010415) SN63HX52CG *9001643835*
Quick reference guide Dishwasher
en
Before using forthefirst time, read theoperating instructions.
Setting up Home Connect
Tip:Connect your appliance to a mobile device. You can con-
veniently change all settings via the HomeConnect app.
1.
Install the HomeConnect app on your mo-
bile device and follow the instructions.
2.
Scan the QR code using the HomeCon-
nect app.
Overview of water hardness settings
You can find an overview of the
water hardness values that can
be selected here.
A table of country-specific units
can be found in the instruction
manual.
Hardness
range
mmol/l Setting
value
Soft 0 - 1.1 H00
Soft 1.2 - 1.4 H01
Medium 1.5 - 1.8 H02
Medium 1.9 - 2.1 H03
Medium 2.2 - 2.9 H04
Hard 3.0 - 3.7 H05
Hard 3.8 - 5.4 H06
Hard 5.5 - 8.9 H07
Setting the water softening sys-
tem
1.
Press ⁠.
2.
To open the basic settings, press
for 3 seconds.
a The display shows Hxx.
a The display shows ⁠.
3.
Press repeatedly until the right
water hardness has been set.
4.
To save the settings, press
for 3 seconds.
Adding special salt
To avoid damage to the appliance, only add special
salt to the dispenser for special salt just before the
programme starts.
1.
Unscrew the lid of the dispenser for special salt
and remove.
2.
On initial start-up: Fill the dispenser right up with
water.
3.
Add the special salt to the
dispenser. The water in the
dispenser is displaced and
forced out. Never add de-
tergent.
4.
Place the lid back on the dispenser and turn to
close.
Adding rinse aid
1.
Press the catch on the lid
of the dispenser for rinse
aid and lift ⁠.
1
2
2.
Add rinse aid up to the
max mark.
max
3.
Close the lid of the dispenser for rinse aid.
a The lid clicks into position.
How to use your appliance
1.
Load the tableware.
Only clean tableware that is suitable for dish-
washers. Remove large remnants of food from
the tableware. Check that the spray arms can ro-
tate freely.
2.
Add detergent.
3.
Switch on the appliance ⁠.
4.
Select the programme.
5.
Start the programme ⁠.
6.
Remove the tableware at the end of the pro-
gramme.
7.
To cancel the programme, press for
approx. 4seconds.
The programme is cancelled and ends after ap-
prox. 1minute.
Programmes
The programme data has been meas-
ured in the laboratory according to
European standard EN60436.
The consumption figures depend on
the programme and additional func-
tion selected.
The running time will change if the
rinse aid system is switched off or
rinse aid needs to be added.
Programme 1) Duration [h:min]
2) Energy [kWh]
3) Water [l]
Intensive 70°
1) 2:05 -2:15
2) 1,300 -1,400
3) 11,5 -14,0
Auto 45-65°
1) 1:40-2:45
2) 0,900-1,500
3) 7,0-15,5
Eco 50°
1) 4:55
2) 0,849
3) 9,5
Speed 65°
1) 1:00
2) 1,300
3) 10,5
Speed 45°
1) 0:29
1
2) 0,800
3) 10,5
Machine Care
1) 2:10
2) 1,350
3) 15,2
Favourite
1) 0:15-0:15
2) 0,050-0,050
3) 4,0-4,0
1
half standard load
Adding detergent
1.
Add the detergent to the
dry detergent dispenser.
15 ml
25 ml
50 ml
2.
Close the lid of the deter-
gent dispenser.
a The lid clicks into position.

Siemens IQ300 SN63HX52CG Specifications

General

Capacity	13 place settings
Noise Level	44 dB
Water Consumption per Cycle	9.5 liters
Number of Programs	6
Delay Start	Yes
Half Load Option	Yes
Annual Water Consumption	2660 liters
Dimensions	81.5 x 59.8 x 55 cm

Summary

Setting Up Home Connect

Install Home Connect App

Install the Home Connect app on your mobile device and follow the instructions for connection.

Scan QR Code for App

Scan the QR code using the Home Connect app to connect your appliance.

Water Softening System Setup

Adjust Water Hardness

Steps to set the water softening system by adjusting water hardness levels.

Adding Detergent and Additives

Add Special Salt

Instructions for filling the special salt dispenser correctly before starting a programme.

Add Rinse Aid

Instructions for filling the rinse aid dispenser up to the max mark.

Add Detergent

How to add detergent to the dry detergent dispenser.

Using Your Appliance

Loading and Starting

Guide to loading tableware, adding detergent, selecting, and starting a programme.

Cancelling Programme

Procedure to cancel the current washing programme by pressing the Reset button.

Cleaning and Maintenance

Cleaning Filters

Steps for cleaning the coarse and micro filters after each wash.

Cleaning Spray Arms

Instructions for removing, cleaning, and reassembling the upper and lower spray arms.

Cleaning Wastewater Pump

Procedure to disconnect, remove filters, and clean the wastewater pump.

Troubleshooting

Water Supply Faults

Troubleshooting error codes related to water supply issues like kinks or blocked filters.

Programme or Drainage Faults

Resolving issues with error codes indicating blocked filters or wastewater pump problems.

Tableware Residue Issues

Causes and solutions for remnants of food, blocked spray arms, or weak wash programmes.

Surface Marks and Spots

Addressing removable streaks on glassware and rust spots on cutlery.