Siemens RWB2007

s
RWB2007 User instructions
Content
Section 1 Introduction and features
Section 2 Factory settings
Section 3 Setting the On/Off times
Section 4 Boost/Advance
Section 5 Review Programme
Section 6 Setting Clock
Section 7 Service Interval*
1. Introduction
The RWB2007 is a 7-day or 5-day-and-2-day twin channel programmer for central heating and hot water.
Features
• Large digital backlit display (timeout 5 minutes)
• 2 or 3 On/Off periods per day
• "Advance“ feature to bring forward the next On/Off period
• “Boost“ feature to give an immediate one hour On
• Automatic summer/winter changeover (summer/winter changeover switch occurs at 02:00)
• Selectable time formats (24-hour and 12-hour (am/pm))
• Built-in calendar
• Copy facility
• Service Interval capable*
2. Factory settings
Before leaving the factory, the RWB2007 was programmed with the correct date and time with the following switching times de-
pendent on the Dip switch setting on the back of RWB (factory default 2 On/Off):
Operating instructions
Switch (1)
: Programming switch. When all programming has been
done this switch must be in Run.
Switch (2): This switch allows you to choose how the
RWB…operates.
Constant: The RWB is permanently ON
ALL DAY: The RWB switches on at the first ON and off at the last
OFF.
AUTO: The RWB switches automatically at the programmed
times.
3. Setting the On/Off times
The RWB2007 is supplied with factory settings (see section 2). If you want to change the factory settings to your own times you
can do so easily. ON/OFF times are adjustable in 10-minute steps.
Setting the central heating
Sliding switch (1) to CH shows all the days of the week with a triangle under Mo. Press YES if you want to program Monday, or
press Day until the triangle goes under the required day, then press YES.
Setting times
The first ON time is 06.00. To change the time, press + or –. When you have reached the desired time, press YES. The first OFF
time is 08.30. Repeat the process until all times are entered for that day.
Note: LIMIT comes in the display if you try to move a programme time forward or backward and it comes up against an existing
time.
Copy
Copy YES/NO appears in the display if you want to copy to the next day. Press YES and repeat for each day that you want to be
the same. If you don’t want to copy, press NO and then set times for each day. When all programming is complete, slide the
switch to RUN.
A6V10464932
Monday - Friday
2 On/Off switching Times
3 On/Off switching Times
On 06.00 Off 08.30
On 06:00 Off 08.30
On 16.30 Off 22.30
On 12.00 Off 14.00
On 16.30 Off 22.30
Weekend
2 On/Off switching Times
3 On/Off switching Times
On 07.00 Off 09.00
On 07:00 Off 09.00
On 16.30 Off 23.00
On 12.00 Off 14.00
On 16.30 Off 23.00
Siemens Building Technologies A6V10464932_enGB_b 2016-07-14 1/2

Siemens RWB2007 Specifications

General

Brand	Siemens
Model	RWB2007
Category	Control Panel
Language	English

Summary

Introduction to the RWB2007

RWB2007 Key Features

Lists key features of the RWB2007 programmer, including display, periods, boost, advance, auto changeover, time formats, calendar, copy, and service interval.

RWB2007 Factory Settings

Default Switching Times Configuration

Details the default factory programmed switching times for central heating and hot water for weekdays and weekends.

Setting OnOff Times

Setting Central Heating Times

Guides on setting central heating ON/OFF times using the programmer's switches and buttons, including day selection and time adjustment.

Adjusting Daily Programme Times

Explains how to adjust the ON/OFF times for each day, noting the 'LIMIT' indicator for overlapping times.

Copying Daily Programme Settings

Describes the facility to copy programmed times from one day to another to simplify setting.

Setting Hot Water Times

Details how to set the ON/OFF times for domestic hot water, similar to central heating settings.

Hot Water Time and Copy Settings

Refers back to the central heating section for instructions on setting times and using the copy function for hot water.

Temporary Overrides

Using the Boost Function

Explains the 'Boost' feature to temporarily switch heating ON for one hour, or extend an existing ON period.

Using the Advance Function

Explains the 'Advance' feature, which brings forward the next ON or OFF period, functional in AUTO or ALL DAY modes.

Reviewing Your Programme

Setting the Clock and Date

Service Interval Reminder