Siemens SIPART PS2 series - Page 20

Electropneumatic positioners
SIPART PS2
Ordering data
Accessories
6/20
Siemens FI 01 · 2009
6
■ Selection and Ordering data Order No.
1)
U.S. certification by FM institute
2)
With a yoke dimension H5 = 95 mm, only the SIPART PS2 in a metal
casing can be used.
C) Subject to export regulations AL: N, ECCN: EAR99
D) Subject to export regulations AL: N, ECCN: EAR99H
Selection and Ordering data Order No.
Accessories
NCS sensor
for non-contacting detection of position
(not for EEx d version), cable length 6 m
(19.68 ft)
6 D R 4 0 0 4 -
7
N N
7
0
Non explosion-proof 8
Explosion-protected, EEx ia/ib 6
For part-turn actuators, without mounting
console
1
For linear actuators up to 14 mm
(0.55 inch), without mounting bracket
2
For linear actuators >14 mm (0.55 inch),
to 130 mm (5.12 inch); Mounting kit same
as for SIPART PS2 (separate ordering item)
The EMC filter module is additionally
required for the controller unit.
(separate order item, see below)
3
Accessories
Alarm module for 3 alarm outputs and
1 binary input (functionality: 2 limit
monitors,
1 fault alarm, 1 binary input)
• Without explosion protection } 6DR4004-8A
• With explosion protection
CENELEC/ATEX
}
6DR4004-6A
• With explosion protection FM/CSA
1)
6DR4004-7A
SIA module (slot-type initiator alarm
module, not for EEx d version)
• Without explosion protection 6DR4004-8G
• With explosion protection
CENELEC/ATEX and FM/CSA
1)
6DR4004-6G
Limit value contact module
(with mechanical ground contacts, not for
EEx d version)
• without explosion protection 6DR4004-8K
• with explosion protection
6DR4004-6K
I
y
module for position feedback signal
(4 to 20 mA)
• Without explosion protection } 6DR4004-8J
• With explosion protection
CENELEC/ATEX
}
6DR4004-6J
• With explosion protection FM/CSA
1)
6DR4004-7J
HART modem for connecting to PC or
laptop
• with RS232 interface }
D)
7MF4997-1DA
• with USB interface
}
D)
7MF4997-1DB
EMC filter module for connection of exter-
nal position sensor (10 kΩ) or NCS sensor
(not for EEx d version)
C73451-A430-D23
Mounting kit for NAMUR part-turn
actuators
(VDI/VDE 3845, without mounting plate) } 6DR4004-8D
The following mounting plates can be used
with the NAMUR part-turn actuator
mounting kit 6DR4004-8D.
Size W x L x H (H = height of shaft butt)
• 30 x 80 x 20 mm }
C)
TGX:16152-105
• 30 x 80 x 30 mm }
C)
TGX:16300-147
• 30 x 130 x 30 mm }
C)
TGX:16300-149
• 30 x 130 x 50 mm }
C)
TGX:16300-151
Mounting kit for other part-turn
actuators
The following mounting plates can be used
together with the NAMUR part-turn
actuator mounting kit 6DR4004-8D.
• SPX (DEZURIK) Power Rac,
sizes R1, R1A, R2 and R2A
}
C)
TGX:16152-328
• Masoneilan Camflex II }
C)
TGX:16152-350
• Fisher 1051/1052/1061,
sizes 30, 40, 60 to 70
}
C)
TGX:16152-364
• Fisher 1051/1052, size 1033 }
C)
TGX:16152-348
Mounting kit for NAMUR linear actuators
• NAMUR linear actuator mounting kit with
short lever arm (2 to 35 mm)
} 6DR4004-8V
• Lever arm for travels from 35 mm to
130 mm (1.38 inch to 5.12 inch)
}
6DR4004-8L
• Reduced mounting kit for linear actuator
(without fixing angle and U-bracket), with
short lever with up to 35 mm travel
(1.38 inch)
}
6DR4004-8VK
• Reduced mounting kit for linear actuator
(without fixing angle and U-bracket), with
long lever with >35 mm travel (1.38 inch)
}
6DR4004-8VL
Mounting kit for other linear actuators
• Retrofitting kit for Moore
series 72 and 750 valve positioners
}
C)
TGX:16152-117
• Fisher type 657/667, size 30 to 80 }
C)
TGX:16152-110
• SAMSON actuator type 3277 (yoke
dimension (H5) = 101 mm
2)
(integrated
connection without tube), not for EEx d
}
6DR4004-8S
Pipe mounting
Mounting bracket for pipe mounting of the
SIPART PS2 position (e.g. when using the
NCS sensor)
}
C)
TGX:16152-336
Additional actuator items can be found at
the following Internet address:
www.siemens.com/sipartps2
Customer-specific actuators available on
request.
} Available ex stock
© Siemens AG 2008