Silex technology SD-320AN

Questions and Answers

C
Colleen StrongAug 16, 2025
How to fix communication errors during Silex technology SD-320AN configuration with Serial Device Server Setup?
- P
  pinedajessicaAug 17, 2025
  If you're experiencing communication errors while configuring your Silex technology Server with Serial Device Server Setup, here are some potential solutions: * Ensure that the SD-300/SD-320AN and your PC are on the same network segment, especially if you don't have a router. * If you're using a DHCP server, make sure your PC is set to 'Obtain an IP address automatically' in the Internet Protocol (TCP/IP) Properties. Alternatively, connect the PC and SD-300/SD-320AN to a standalone Ethernet Hub to isolate the issue. * If the SD-300/SD-320AN was previously used on another network, its settings might be preventing communication. Try resetting the SD-300/SD-320AN to its factory default settings.
W
Wendy CannonAug 22, 2025
What to do if the Silex technology SD-320AN IP address is already in use?
- Z
  Zachary MullenAug 22, 2025
  If you suspect that the IP address assigned to your Silex technology Server (SD-300/SD-320AN) is being used by another device on the network, follow these steps: Turn off the SD-300/SD-320AN. Open the Windows Command Prompt and ping the IP address of the SD-300/SD-320AN. If you receive a reply while the SD-300/SD-320AN is off, another device is using the same IP address. Change the IP address of either the SD-300/SD-320AN or the other conflicting device.
D
Derek AndersonAug 27, 2025
How to check serial cable connection on Silex technology SD-320AN Server?
- C
  cblackAug 27, 2025
  To ensure proper connection between your Silex technology Server (SD-300/SD-320AN) and a serial device, verify that the serial cable is securely plugged into both the SD-300/SD-320AN and the serial device. If possible, try replacing the serial cable with a spare to rule out a faulty cable.
A
amandasmithAug 31, 2025
Why Silex technology SD-320AN Server turns on in wireless LAN mode?
- V
  Valerie ConnerAug 31, 2025
  If your Silex technology SD-320AN Server is turning on in wireless LAN mode when connected to a 10BASE-T Ethernet HUB via a network cable, you can extend the time the device waits before recognizing a wired LAN connection. Here’s how: 1. Access the SD-320AN Web page and click 'WEB console' from the left menu. 2. Enter 'SET NW STARTDELAY 5' in the field and click Enter. 3. Enter 'SAVE' in the field and click Enter. 4. Click 'Restart' under Maintenance to restart SD-320AN.
O
oconnellwilliamNov 6, 2025
Why is my Silex technology Server (SD-300/SD-320AN) not showing up in the Serial Device Server Setup search?
- E
  Elizabeth MullinsNov 6, 2025
  There are several reasons why your Silex technology Server might not be showing up in the Serial Device Server Setup search: * There may be a connection, power, or operational issue with the SD-300/SD-320AN or the Ethernet Hub it's connected to. Check the LED status, replace cables, and reboot devices. * The SD-300/SD-320AN may not have finished starting up. It can take up to 30 seconds to be ready. Wait and then click 'Search' again. * The SD-300/SD-320AN and your PC might not be on the same network segment. Place them in the same network segment for initial configuration. * The SD-300/SD-320AN may have settings from a previous network that are interfering with communication. Reset it to the factory default settings. * Security software like a firewall could be blocking communi...
K
Kelly RobinsonNov 11, 2025
What to do if serial devices are not displayed in SX Virtual Link for Silex technology SD-320AN?
- G
  Glenn LopezNov 11, 2025
  If serial devices are not being displayed or are only temporarily displayed in SX Virtual Link for Serial Device Server with your Silex technology Server, consider the following: * Check the connection, power, and operation of the SD-300/SD-320AN and the Ethernet Hub. Look at the LED status, replace cables if needed, and reboot the devices. * Ensure the SD-300/SD-320AN has fully started up. It can take about 30 seconds. After that, refresh SX Virtual Link for Serial Device Server. * Security software, like a firewall, may be interfering. Add SX Virtual Link for Serial Device Server to your security software's exception list. * The IP address assigned to the SD-300/SD-320AN might not be able to communicate with your PC. Verify your PC's IP address using the Windows Command Prompt (...