EasyManua.ls Logo

Silverline 427558 - User Manual

Silverline 427558
64 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Version date: 15.01.24
silverlinetools.com
XXXXXX
FR Pistolet à graisse pneumatique 400 cm³
DE Druckluft-Fettpresse, 400 cm³
ES Pistola de engrase neumática 400 cm³
IT Ingrassatore pneumatico 400 cm³
NL Pneumatische vetspuit, 400 cm³
PL Smarownica pneumatyczna 400 cm³
EE Pneumomäärdepüstol 400cc
LT Pneumatinis tepimo pistoletas 400cc
LV Pneimatiskāsmērvielupistole400cc
Air Grease Gun 400cc 280mm
427558
427558_OwnerManual.indd 1427558_OwnerManual.indd 1 16/01/2024 08:5916/01/2024 08:59

Questions and Answers

  • R
    Rachel MorganJul 29, 2025
    Why is my Silverline Tool operating slowly?
    • C
      Cody FullerJul 29, 2025
      If your Silverline Tool is operating slowly, it might be due to incorrect pressure. Ensure you set the correct air pressure according to the specifications. Also, dirt within the mechanism can cause this issue; try pouring air tool oil into the air inlet as per maintenance instructions. An air blockage could also be the culprit; operate the tool in short bursts to clear any blockages. Check all fittings and the hose for air leaks, correcting any issues by re-tightening, using PTFE tape, or replacing parts as needed. Finally, a blockage in the gauze mesh filter could be the cause; remove the Quick Connector and clean the mesh filter.
  • D
    Daniel CrawfordAug 3, 2025
    What to do if my Silverline Tool is dispensing a low amount of grease?
    • P
      pchapmanAug 3, 2025
      If your Silverline Tool is dispensing a low amount of grease, it could be due to low compressor pressure. Increase the compressor air pressure within the specified range. Alternatively, the grease level in the chamber may be low; refill the chamber.
  • J
    Jacqueline Lewis DDSAug 8, 2025
    Why does my Silverline Tool gun fail to operate?
    • J
      jenkinsveronicaAug 8, 2025
      If your Silverline Tool gun fails to operate, it may be due to an air pocket. Follow the instructions for bleeding the grease chamber.
  • M
    Michael ParsonsAug 13, 2025
    What to do if no grease is dispensed from my Silverline Tool?
    • J
      Jeremiah HaneyAug 13, 2025
      If no grease is dispensed from your Silverline Tool, it could be that the plunger mechanism hasn't been released. Try pressing the Plunger Release.
  • K
    Kelly WillisAug 18, 2025
    How to fix a seized Silverline Tool?
    • T
      Teresa CainAug 18, 2025
      If your Silverline Tool is seized, it may be due to dirt or rust in the mechanism. Try the solutions suggested for a tool operating slowly. If that doesn't work, gently tap the tool with a soft mallet.
  • V
    vsimpsonAug 23, 2025
    What to do if my Silverline Tool will not stop?
    • A
      Alexander GomezAug 23, 2025
      If your Silverline Tool will not stop after the trigger is fully released, it could be that the throttle valve O-ring or valve seat is damaged. In this case, have the tool repaired at an authorised Silverline service centre.

Summary

Product Specifications

Safety and Preparation

General Safety Warnings

Critical safety precautions and warnings for the safe operation of the grease gun.

Before Use: Fitting the Quick Connector

Details on how to attach the quick connector for air supply connection to the tool.

Operational Guidelines

Filling with Grease

Methods for loading grease into the gun, including cartridge, container, or pump.

Bleeding the Grease Chamber

Procedure to remove trapped air from the grease chamber after filling.

Operation

Step-by-step guide on how to operate the air grease gun.

Maintenance and Care

Daily Procedures and Storage

Daily Maintenance Procedure

Routine lubrication and checks for daily upkeep of the air tool.

Troubleshooting

Silverline 427558 Specifications

General IconGeneral
BrandSilverline
Model427558
CategoryTools
LanguageEnglish

Related product manuals