Simon S82 User Manual

Lector biométrico en red S82
Network biometric reader S82
Art. 8902009-039
Alimentación:
Consumo Máx (±5%):
Capacidad de huellas:
Comunicación:
Distancia del cable:
Lector de huellas:
1:1000 tiempo de
respuesta:
Seguridad:
Temperatura de uso:
Humedad:
Dimensiones (mm):
Protección:
Personalizable:
Power supply :
Max Consumption(±5%):
Fingerprint capacity:
Interface:
Cable distance:
Fingerprint Sensor Type:
1:1000 identication
time:
Security:
Operating Temperatures:
Humidity:
Dimensions (mm):
Protection standard:
Customizable:
9-14Vdc
100mA
Hasta 100 huellas.
Wiegand 8 to 128 bits; Por defecto:
Wiegand 26bit
50m
Capacitativo
970 msec, incluido tiempo de extracción
de características
Tamper antisabotaje
-20ºC a +50ºC
5% a 93% HR sin condensación
72x72x45
IP40
Simon 82 Detail, Simon 82 y 82 Nature
9-14Vdc
100mA
Up to 100 prints.
Wiegand 8 to 128 bits; Default: Wiegand
26bit
50m
Swipe Capacitive
970 msec, including feature extraction
time
Tamper
-20ºC a +50ºC
5% to 93% RH without condensation
72x72x45
IP40
Simon 82 Detail, Simon 82 and 82 Nature
Conexión con un lector de
tarjetas o teclado adicional
Connection to additional card
reader or keypad
Central Controladora
Access Control
Art. 8902013-039
990826 17-05-2016
SIMON, S.A. Diputación, 390-392 / 08013 Barcelona
Servicio de asesoramiento Técnico - Tel.902109700 E-mail: sat@simon.es
Art. 8900071- 030/038/093
Tamper
12 V DC
LG-
LEDs
RS485
WIEGAND
LR-
B
A
D1
D0
GND
12V DC 9-14V DC 9-14V DC
GND Tierra Ground
A RS485 A RS485 A
B RS485 B RS485 B
LR- LED Rojo -
Red LED -
LG- LED Verde - Green LED -
D1 Datos 1 Data 1
D0 Datos 0 Data 0
Tamper Interruptor antisabotaje(NO) Tamper Switch NO
Tamper Interruptor antisabotaje(NO) Tamper Switch NO
ES
Cableado / Wiring
Conexión / Connection
Montaje / Mounting
1 2 3
www.simon.es
EN
Amarillo / Yellow
Blanco / White
Rojo / Red
Negro / Black
Naranja / Orange
Verde / Green
Max 50 m
12V dc
Ac. Granted LED
Ac. Denied LED
D1
A
Led Green -
Led Red -
GND
GND
12V Out
D0
D0
D1
RS 845 A
RS 845 B
B

Simon S82 Specifications

General

Brand	Simon
Model	S82
Category	Switch
Language	English

Summary

Connecting Biometric Reader with Keypad or Proximity Reader

Connecting readers and configuring software

Connect readers with cable and configure types (BIO+RFID, BIO+Keypad) in software.

Setting up keypad as slave reader

Configure keypad to operate as a slave reader unit.

Connecting Biometric Readers to Controller

Communication lines, power, and enrollment

Covers DATA, RS485, power, and PC fingerprint enrollment.

RS485 line connection and configuration

Daisy chain topology, cabling, and termination for RS485.

Connecting Biometric Readers with TCP/IP Controllers

TCP/IP connection, RS485 termination, and multi-reader notes

Covers TCP/IP connection, RS485 termination, and multi-reader network configuration.

RS485 Tuning and Finger Swiping

RS485 termination resistor configuration

Using 120 Ohm, external, and CAT 5 termination.

Recommended finger swiping technique

Instructions for correct finger placement and movement.

Biometric Reader Configuration in SIMON Software

Adding and checking reader status

Add reader to software and verify its online status and type.

Enrolling Fingerprints from a Reader

User creation, enrollment, and distribution

Create user, enroll fingerprint, and check memory status.

Managing Fingerprints: Deleting and Uploading

Deleting user and specific fingerprints

Remove single user, all users, or specific fingerprints from the reader.

Uploading all users' fingerprints to reader

Transfer user profiles and fingerprints from software to reader.

Reader Management: Firmware, Configuration, and Advanced Settings

Firmware update and configuration transfer

Update reader firmware and send configuration settings.

Advanced settings: unknown finger, backlight, buzzer, tolerance

Configure advanced options like unknown finger handling, backlight, buzzer, and tolerance.

Custom Wiegand Configuration

Setting up custom Wiegand formats and parameters

Select and configure non-standard Wiegand formats and transmission parameters.

Wiegand Protocol and Safety

DATA lines, 26-bit format, and parity calculation

Details on DATA signal logic, 26-bit format, and parity calculation.

Installation and cleaning precautions

Safety guidelines for device installation and maintenance.