Simplex 4100-5120 - User Manual

Cautions, Warnings, and Regulatory Information
READ AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation manual. These instructions must be followed to avoid damage to
this product and associated equipment. Product operation and reliability depend upon proper installation.
DO NOT INSTALL ANY SIMPLEX™ PRODUCT THAT APPEARS DAMAGED Upon unpacking your Simplex product, inspect the contents
of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify an authorized Simplex
product supplier.
ELECTRICAL HAZARD Disconnect electrical field power when making any internal adjustments or repairs. All repairs should be
performed by a representative or an authorized agent of your local Simplex product supplier.
STATIC HAZARD Static electricity can damage components. Handle as follows:
• Ground yourself before opening or installing components.
• Prior to installation, keep components wrapped in anti-static material at all times.
EYE SAFETY HAZARD Under certain fibreoptic application conditions, the optical output of this device may exceed eye safety limits. Do
not use magnification (such as a microscope or other focusing equipment) when viewing the output of this device.
FCC RULES AND REGULATIONS – PART 15. This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
SYSTEM REACCEPTANCE TEST AFTER SOFTWARE CHANGES To ensure proper system operation, this product must be tested in accordance with
NFPA72® after any programming operation or change in site-specific software. Reacceptance testing is required after any change, addition or deletion
of system components, or after any modification, repair or adjustment to system hardware or wiring.
All components, circuits, system operations, or software functions known to be affected by a change must be 100% tested. In addition, to ensure that
other operations are not inadvertently affected, at least 10% of initiating devices that are not directly affected by the change, up to a maximum of 50
devices, must also be tested and proper system operation verified.
NFPA 72® is a registered trademark of the National Fire Protection Association.
Introduction
This publication provides an overview of the features, specifications, and capabilities of the TrueAlert power supplies (TPS). These supplies provide
auxiliary power, a battery charger, and three Signaling Line Circuits (SLC). Each of which provides control and power to the full range of TrueAlert
appliances.
The TrueAlert power supplies are identical to each other with the following exceptions:
• 4100-5120 Domestic (US) version, requires a 120 VAC power source.
• 4100-5121 Canadian version, requires 120 VAC power source and provides battery cutout option. After installing a 4100-5121, refer to
“Enabling Low Battery Cutout Option” in the ES Panel Programmer’s Manual (574-849) for information on enabling this option.
• 4100-5122 International version, uses a 220/240 VAC power source.
If you are wiring Class A circuits, you need to install a 4100-5124 Class A Adapter Card onto the TrueAlert Power Supply before installing the power
supply. Refer to Document # 579-337 for more information.
This product is compatible with the 4100U and 4100ES Fire Alarm Control Panel (FACP).
Note: Verify FACP System Programmer, Executive, and Slave Software compatibility when installing, or replacing system components. Refer to the
Technical Support Information and Downloads website for compatibility information.
579-336 Rev. M
4100-5120, 4100-5121, 4100-5122 TrueAlert Power Supply Installation Instructions
*0579336M*

Summary

Cautions, Warnings, and Regulatory Information

Safety Precautions

Covers electrical, static, and eye safety hazards during installation and operation.

Regulatory Compliance and Testing

Includes FCC Rules, NFPA standards, and system reacceptance testing requirements.

Introduction to the TrueAlert Power Supply

TPS Overview and Models

Describes the TrueAlert Power Supply (TPS) features, specifications, and available models.

Additional TPS Features

Details TrueAlert operation, diagnostic capabilities, battery cutout, and visual synchronization.

Technical Specifications

Input;Output;Battery Specifications

Details AC input, DC output, and battery charger specifications for the TPS.

TPS Current Consumption and Environmental

Lists battery standby current requirements and operating environmental conditions.

Mounting the TPS

Mounting Procedure Steps

Describes the steps for physically mounting the TPS unit onto an expansion box and connecting to the PDI.

TPS Configuration

Earth Fault Detection Configuration

Explains how to set the jumper for enabling or disabling earth fault detection.

Setting the Device Address

Details the use of DIP switches for setting the card's address within the FACP.

Power Connections

PDM;Battery Connections Diagram

Illustrates the wiring diagram for connecting the Power Distribution Module (PDM) and batteries.

Compatible Devices

TrueAlert Device List

Lists compatible TrueAlert devices, their PIDs, and installation document numbers.

General Wiring Guidelines

Wiring Standards and Material

Covers conductor types, code compliance (NFPA 70, NEC), and specific wiring material requirements.

Power-Limited Wiring Guidelines

Power-Limited vs. Non-Power Limited Routing

Differentiates routing and handling for power-limited and non-power-limited wiring within the FACP.

Wiring Class A Circuits

Class A Guidelines and Requirements

Details Class A wiring, device limits, synchronization, and wire resistance parameters.

SLC Wire Length Calculations

Provides tables for calculating maximum SLC wire lengths based on appliance current load.

Class A Wiring Diagrams

Class A Wiring Configurations

Illustrates Class A wiring diagrams, both with and without isolators.

Class B Wiring Guidelines

Class B Guidelines and Requirements

Outlines Class B wiring rules, device limits, synchronization, and wire resistance.

Class B Wiring Diagrams

Class B Wiring Configurations (No Isolators)

Shows Class B wiring diagrams without isolators, including T-Tapping allowed.

Class B Wiring Configurations (With Isolators)

Illustrates Class B wiring with isolators and provides SLC wire length calculation formula.

Wiring AUX Power

AUX Power to Power-Limited Wiring

Diagram and notes for connecting AUX power to power-limited circuits with supervision.

Compatible AUX Power Devices

Lists devices compatible with the AUX Power output as defined by UL.

Troubleshooting

System Trouble Indicators

Explains the system trouble indicator LEDs and their corresponding trouble codes.

Simplex 4100-5120 Specifications

General

Brand	Simplex
Model	4100-5120
Category	Power Supply
Language	English