Simplex 4100-5126 RPS - User Manual

SPS/RPS
Installation Instructions
 2005, 2008, 2009, 2011 SimplexGrinnell LP. All rights reserved.
Specifications and other information shown were current as of publication and are subject to change without notice.
Simplex and the Simplex logo are trademarks of Tyco International Ltd. and its affiliates and are used under license.
579-246
Rev. K
This publication describes the installation procedure for the following 4100-Series System Power
Supplies (SPS) and Remote Power Supplies (RPS):
 4100-5111/5112 SPS (120 VAC) (mounts to expansion bays only)
 4100-5125/5126 RPS (120 VAC)
 4100-5113 SPS (220/230/240 VAC) (mounts to expansion bays only)
 4100-5127 RPS (220/230/240 VAC)
These products are compatible with 4100U and 4100ES Fire Alarm Control Panels
(FACP).
IMPORTANT:
 The SPS described in this document are not physically the same as the SPS
used in the CPU bay.
 Verify FACP System Programmer, Executive, and Slave Software compatibility
when installing, or replacing system components. Refer to the Technical
Support Information and Downloads website for compatibility information.
This publication discusses the following topics:
Topic See Page #
Cautions and Warnings 2
Introduction to the SPS and RPS 3
Mounting 7
Configuring the SPS and RPS 8
Internal Wiring 10
NAC Field Wiring 12
IDNet Field Wiring (SPS only) 23
Auxiliary Power Wiring 26
Auxiliary Relay Wiring 29
Troubleshooting 31
City and relay connections can be made from the SPS (the RPS supports relay connections only).
Refer to the City and Relay Card Installation Instructions (574-839) to install a relay card to the
SPS, or a city card to the SPS or RPS.
To find out more about the CPU bay version of the SPS, which operates in the same way as the
expansion bay version of the SPS but mounts differently, refer to the 4100ES Fire Alarm System
Installation Guide (574-848).
For information on Expansion Power Supplies (XPS), refer to XPS and XNAC Installation
Instructions (574-772).
Introduction
In this Publication
Related
Documentation
firealarmresources.com

Simplex 4100-5126 RPS Specifications

General

Model	4100-5126
Input Voltage	120/240 VAC
Input Frequency	50/60 Hz
Output Voltage	24 VDC
Type	Remote Power Supply
Output Current	6 A
Operating Temperature	0°C to 49°C
Storage Temperature	-20°C to 60°C
Humidity	0% to 93% non-condensing
Mounting	Wall Mount

Summary

Cautions and Warnings

Safety and Compliance Warnings

Key safety precautions, electrical hazards, static discharge, FCC compliance, and reacceptance testing requirements.

Mounting the SPS and RPS

Mounting Procedure

Step-by-step instructions and diagram for physically mounting the SPS or RPS assembly to an expansion cabinet.

Configuring the SPS and RPS

Jumper Settings

Explains the function and configuration of jumpers P1, P2, and P3 on the SPS/RPS.

Setting the Device Address

Details how to set the device address using DIP switch SW1 on the SPS/RPS.

NAC Field Wiring

Compatible Appliances (Table 7)

List of compatible appliances and accessories for Special Application NACs.

Cooper Wheelock Appliances (Table 8)

List of Cooper Wheelock appliances compatible with SPS/RPS for Special Application NACs.

Class A NAC Wiring

Class B NAC Wiring

IDNet Field Wiring (SPS Only)

Class A Wiring

Class B Wiring

Auxiliary Power Wiring

Wiring Diagrams

Auxiliary Relay Wiring

Relay Wiring Diagram

Troubleshooting SPS and RPS

Display Messages and Causes

Describes common trouble messages on the 4100 display and their possible causes.