What causes stepped cutting with a Simplicity Cobalt?
If your Simplicity Lawn Mower is causing stepped cutting, ensure the deck is leveled correctly, the tires are properly inflated, and the blades are not damaged and are correctly installed. Repair or replace the deck shell if damaged, and repair or replace the spindle if bent or loose.
How to fix streaking with Simplicity Cobalt?
If your Simplicity Lawn Mower is leaving streaks, several factors could be the cause. Your blades might not be sharp enough, so sharpen them. They could also be worn down too far, in which case you should replace them. Ensure you are mowing at full throttle and not going too fast. A deck plugged with grass can also cause streaking, so clean it out. Finally, make sure you are overlapping your cutting rows sufficiently, especially when turning, as your effective cutting width decreases.
How to fix a Simplicity Cobalt Lawn Mower when the drive belt slips?
If the unit drive belt on your Simplicity Lawn Mower is slipping, clean the pulleys or belt if they are greasy or oily. If the tension is too loose, adjust the spring tension. Replace the belt if it is stretched or worn.
What to do if my Simplicity Cobalt Lawn Mower engine starts hard or runs poorly?
If your Simplicity Lawn Mower engine starts hard or runs poorly, it could be due to a fuel mixture that is too rich. Try cleaning the air filter and checking the choke adjustment. Another cause could be faulty, fouled, or incorrectly gapped spark plugs. Clean, gap, or replace them as needed.
Why is the engine exhaust black on my Simplicity Cobalt?
Black exhaust from your Simplicity Lawn Mower engine usually indicates that the engine is getting too much fuel. This could be due to a dirty air filter, so replace it. Another cause could be that the engine choke control is in the CLOSED position; if so, open the choke control.
Why is my Simplicity Cobalt leaving streaks?
To resolve streaking with your Simplicity Lawn Mower, sharpen or replace the blades if they are dull or worn. Ensure you are mowing at full throttle and not moving too fast. Clean out the mower deck if it's plugged with grass, and make sure to overlap cutting rows sufficiently, especially when turning.
What to do if the engine runs, but the rider will not drive on my Simplicity Cobalt?
If your Simplicity Lawn Mower engine runs but the rider won't drive, it could be due to hydraulic release valves being in the “open” position; turn them clockwise to close them. Another cause could be a broken belt.
What causes my Simplicity Cobalt to not engage?
If your Simplicity Lawn Mower does not engage, it could be due to electrical wiring damage; locate and repair the damaged wire. Another cause could be battery voltage that is too low.
What to do if the mower drive belt slips or fails to drive on my Simplicity Cobalt Lawn Mower?
If the mower drive belt slips or fails to drive on your Simplicity Lawn Mower, the idler pulley spring may be broken or not properly attached; repair or replace it as needed. The mower drive belt could also be broken; replace the drive belt.
Why is there excessive mower vibration in my Simplicity Lawn Mower?
Excessive vibration in your Simplicity Lawn Mower can be caused by several factors. Check if the blade mounting bolts are loose and tighten them to 70 ft.lbs (94 Nm). Bent mower blades, spindles, or pulleys can also cause vibration, so inspect and replace them as necessary. Additionally, unbalanced mower blades can contribute to this issue; remove, sharpen, and balance the blades. Finally, ensure the belt is installed correctly.
General| Brand | Simplicity |
|---|---|
| Model | Cobalt Series |
| Category | Lawn Mower |
| Language | English |
Learn about the operator's manual for safety information and operation details.
Guidelines for operating the machine safely on slopes, including angle and traction.
Proper use of the roll bar and seat belt for rollover protection and safety.
Safe fuel handling, enclosed area warnings, and general operational safety.
Safe gasoline handling, service precautions, safety interlocks, and icons.
Locating model and serial numbers for parts, service, and information.
Brief descriptions of essential controls like Deck Lift, Parking Brake, and PTO switch.
Operation of ignition, throttle, speed, lights, and seat controls.
Steps before starting, checks, and initial driving practice for zero-turn riders.
How to mow, patterns, timing, and recommendations for optimal results.
Techniques for mulching grass and safely attaching a trailer.
A detailed schedule of safety, rider, and engine maintenance tasks based on operating hours.
Procedures for checking fuel, oil, and filters, including replacement steps.
Steps for removing, inspecting, and servicing mower blades.
Adjusting controls, brakes, suspension, and replacing belts.
Diagnosing and resolving common engine and rider operational problems.
Diagnosing and resolving common cutting problems like streaking and scalping.
Detailed specifications for the engine, transmissions, chassis, and dimensions.
Information on obtaining service and parts manuals for the unit.
To Next Page