ftfi:nuit~$JJ{
I Before operation
il
Xi.:
~•~m•~-~~~-~.m~~~:
·~-~~~m*mm.mmaM~.
~*~•Mm~~~$~~.#~~~~~Mo
•
UJQiA~Bi~NIE~,
tm~~~il:ii~~NIEUJJJo
·~•~oo*~~Bi~*m•~rr~Bi~-~.
mm~m*mo
•
UJJJiA~tJL~~1J~~NIE1iiUo
·~m*m~~-~~.m•~~IE~~ariE~~~~~~o
CAUTION:
To avoid malfunction and damage
of
the machine, confirm the following:
• Before you put the machine into operation for the first time after the set-up, clean it thoroughly. Remove all dust
gathering during transportation and oil it well.
• Confirm that the voltage has been correctly set. Confirm that the power plug has been properly connected to the
power supply.
• Never use the machine in the sate where the voltage type
is
irrerent from the designated one.
• Confirm that the direction
of
rotation
of
the motor pulley is correct.
• Operate your machine at the normal sewing speed
or
less for the first month after the set-up.
3f$nutr.Jtt~$JJ{
I Pre-start Checks
I,
~f.ti*J*:JJD~~~fm7f$o
2,
fJL·~~M.
MJ:~:9r1MIJti~~~~~B>ttt17~,
tt:~.
~fm~J~o
3,
~lll*JJ~ffl~~
-
~
~
1=J:t,
m:ti~Ai:il~fl£194!¥~ftft4000ftutfi~m1'F!&o
4.~~~~m~~J:~~tt:.
~-~•.
~Bi&•m.~m~NIEUJJJo
I. The machine shall not be started running until the completion
of
oiling.
2.
The rotating direction
of
the balance wheel, when the machine is started running, shall be in counter-clockwise one.
(View from the right side
of
the balance wheel.) A warning shall be given in advance against making the machine run
while balance wheel turning clockwise.
3.
The machine shall be under operation at less than
4,000
S.P.M. for the first month.
4. Check power source, voltage, and phase number to see whether they are in accordance with the ratings on the name
plate
of
the motor to be used.
=
..
f:fJftit~$JJ{
I Operating instructions
1,
tJL•~ffiB>t,
i~m:trf-=¥1itl!JJtt~r$o
2.m.~f!iM,
mm:trt-=f.ffi~AM~ff~~l*.lo
3.m•UJJJ~~tt$,
~~f.t~l:~o
4.**~~m**$,
~rmttJ:~•~.
~~mm~~-~~-matoo.m~~tt:~.
*~tt~~~~•
m•fl]ifiJo
5,
m•~f!ia-t.
mm:m--=r-1~,
~2lt~;tt't*W~:ili~~"J:~.
"V"
m&:m,
~~m.
-tl!~~:tE*WntJt~
E f(]
j)#
lli
o
6,
•m&:m~&~m•a.t.mm7f~m•o
1.
Do not put your hands under the lower part
of
the needle when the machine
is
running.
2.
Do not put your fingers into the thread take-up lever cover when the machine is running.
3.
Only when the machine stops can you turn the balance wheel by hand.
4. After the motor switch being turned off, due to inertia, the motor will continue to rotate for a while. Be careful not to
have the machine tilted unless
is
stops.
5.
Keep away from the balance wheel, V-belt, winder and the motor.
6.
Do not start running the machine during mounting
or
replacing the belt cover, finger guard, etc.
-1-
To Next Page
Loading...
Need help?
General
