12
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol
6
will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 93.5 dB(A) and the sound
power level 104.5 dB(A) (standard deviation: 3 dB),
and the vibration
.
(triax vector sum; uncertainty
K = 1.5 m/s²)
.
when surface grinding 11.6 m/s²
.
when polishing 8.5 m/s²
.
when sanding 6.9 m/s²
!
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
- the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
!
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
Meuleuse d’angle 9012
INTRODUCTION
• Cet outil sert au meulage, au tronçonnage et à l’ébarbage
de pièces en métal et en pierre sans utiliser de l’eau;
combiné avec des accessoires spéciques, cet outil peut
également servir au brossage et au ponçage
• Cet outil n’est conçu pour un usage professionnel
• Les opérations de coupe avec disques à tronçonner
abrasifs ne sont autorisées que si une protection
accessoire SKIL 2610Z04675) est utilisée
• Lisez et conservez ce manuel d’instruction
3
CARACTERISTIQUES TECHNIQUES
1
ELEMENTS DE L’OUTIL
2
A Arbre
B Bride de serrage
C Clé
D Bouton de blocage de l’arbre
E Poignée auxiliaire
F Protège-main
G Interrupteur marche/arrêt de sécurité
• On/o safety switch G
w
- switch on tool
w
a
! before the accessory reaches the workpiece, the
tool should run at full speed
- switch o tool
w
b
!
the workpiece
! the accessory continues to rotate for a short time
• Grinding
e
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
• Cutting
r
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on tool
head, in order to prevent the tool from being pushed out
of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of the
cutting disc do the work
- the working speed of the cutting disc depends on the
material to be cut
- do not brake cutting discs with side pressure
• Holding and guiding the tool
- always hold the tool rmly with both hands, so you will
have full control of the tool at all times
! while working, always hold the tool at the grey-
t
- provide for a secure stance
- pay attention to the direction of rotation; always hold the
tool so, that sparks and grinding/cutting dust y away
from the body
- keep ventilation slots H
2
uncovered
APPLICATION ADVICE
• Instead of ange B
2
the “CLIC” quick-clamping ange
(SKIL accessory 2610388766) can be used; grinding/
cutting discs can then be mounted without the use of
accessory keys
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots H
2
)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
To Next Page
Loading...
