EasyManua.ls Logo

Skil BI9502-00 - User Manual

Skil BI9502-00
76 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WARNING: To reduce the risk of injury, the user must read and understand the
Owner’s Manual before using this product. Save these instructions for future reference.
AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et
comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide
afin de pouvoir le consulter ultérieurement.
ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender
el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para
consultarlas en caso sea necesario.
Owner’s Manual
Guide d’utilisation
Manual del propietario
8” Bench Grinder
Meuleuse de table de 8 po
Amoladora de banco de 8 pulgadas
For Customer Service
Pour le service à la clientèle
Servicio al cliente
1-877-SKIL-999
OR
www.skil.com
Model/ Modelo/ Modèle: BI9502-00

Table of Contents

Questions and Answers

  • C
    Christopher PierceJul 29, 2025
    What to do if my Skil BI9502-00 Grinder will not start?
    • M
      Michael RossJul 29, 2025
      If your Skil Grinder won't start, the possible causes include: the power cord is not plugged in (ensure it is plugged into a functioning power outlet); a tripped fuse or circuit breaker (replace the fuse or reset the breaker); a damaged cord (have it replaced by an authorized SKIL service center or service station); or a burned-out switch (have it replaced by an authorized SKIL service center or service station).
  • A
    Angela WilsonAug 8, 2025
    Why is there excessive vibration in my Skil Grinder?
    • S
      Sara CarrollAug 8, 2025
      Excessive vibration in your Skil Grinder can be caused by the grinding wheel not being fixed properly. Re-install the grinding wheel following the 'WHEEL REPLACEMENT' section in this manual. Alternatively, the bench grinder might not be securely mounted to the stand or workbench; in this case, tighten all mounting hardware.
  • W
    William WilliamsAug 18, 2025
    Why does the wheel of my Skil BI9502-00 not come up to speed?
    • D
      Deborah MccarthyAug 18, 2025
      If the wheel of your Skil Grinder does not come up to speed, it might be due to an extension cord that is too light or too long; replace it with an adequate cord. Another possible cause is low supply voltage; in this case, contact your electric company.

Summary

General Power Tool Safety Warnings

Work Area Safety

General guidelines for maintaining a safe work environment, keeping it clean and well-lit.

Electrical Safety

Precautions related to power supply, cords, grounding, and avoiding contact with earthed surfaces.

Personal Safety

Measures to protect the operator, including staying alert, using PPE, and preventing unintentional starting.

Bench Grinder Safety Warnings

Additional Safety Rules

Tool Use

Tool Care

Connection to a Power Source

Extension Cords

Assembly

Fitting the Spark Deflector & Eye Shield Assembly

Adjusting and Fitting the Eye Shields

Fitting the Work Rests

Fitting Coolant Tray

Permanent Mounting of Bench Grinder to Workbench

Temporary Mounting of Bench Grinder to Workbench

Operation

On;Off Switch

Instructions on how to start and stop the bench grinder using the switch.

Maintenance

Service

Guidelines for professional servicing and repairs by authorized personnel.

General Maintenance

Routine checks for damage, loose parts, and replacement recommendations.

Cleaning

Lubrication

Wheel Replacement

Troubleshooting

Skil BI9502-00 Specifications

General IconGeneral
TypeAngle Grinder
Voltage120 V
Speed11000 RPM
No Load Speed11000 RPM
Cable Length6 ft
Wheel Diameter4.5 inches
Disc Diameter4.5 inches
Spindle Thread5/8-11

Related product manuals