4
NOTE:
Please ensure the positive plus sign on the battery matches
the positive plus sign on the battery holder.
With the battery correctly inserted
the red LED on the printed circuit
board will ash once. Carefully place
the combined circuit board and
battery into enclosure 1, and snap
enclosure 2 into place.
STARTING YOUR VEHICLE
Using the keypad PIN code
To disarm the security system, the correct PIN code must be
entered.
To enter the PIN code, proceed as follows:
1. Turn ON the vehicle’s ignition, the keypad backlight and
red LED will illuminate.
2. Enter your PIN code, the keypad will give a conrmation
bleep each time a button is pressed.
3. Conrm entered PIN code by pushing the # button.
4. If successful the keypad will double beep, the red LED
will turn OFF, and the green LED will turn ON.
5. The security system is now disarmed – The keypad
backlight will go out and the green conformation LED will
remain on.
6. If the incorrect code has been entered, the keypad
will emit one long beep. In this instance, switch o the
ignition and go back to step 1.
NOTE:
Once the keypad has accepted a correct code entry, it will stay
in this state and will remain so until the ignition is switched
OFF.
The PIN code must be entered each time the ignition is
switched on, except when the ignition has been switched OFF
for less than 4 minutes approx. (read section passive arming).
Using Personal Transceiver
It is possible to disarm the system using Personal Transceiver,
proceed as follows:
1. With the Personal Transceiver within a 5 metre range of
the vehicle.
2. Turn ON the ignition and wait until a double beep will
sound, the keypad red LED will turn OFF, and the green
LED will turn ON. (Normally This could take up to 10
seconds)
3. The system is disarmed, now you can start the engine.
ATTENTION!!!
Do not leave the Personal Transceiver inside the vehicles or in
a 5 metre range, whilst the vehicle is not attended. This device
overrides your security, and should therefore be kept at home
in a safe place or on your person at all times.
NOTE!!!
The signal from the Personal Transceiver is transmitted
once per 10 seconds. If you are in an area with a lot of
digital transmissions, the communication between Personal
Transceiver and other security system’s components may take
longer.
PIN CODES
PIN codes: The Skybrake TOUCH keypad can store up to 5
User codes and one Master code, the Master code is used to
add and delete your ve user codes. Therefore a secondary
user should be given one of the ve possible User codes,
which they can not modify add or delete other codes with.
Only the Master code can do this, in the event of a Master code
being lost or forgotten, please refer to the PIN code card also
supplied with this system.
All PIN codes can be 4 to 8 digits long; the PIN code entry is
conrmed with the # key.
Example: Factory default is “0000” then press the # to
conrm, you will hear two short beeps and
the green LED light will illuminate. If the
incorrect code has been entered the keypad
will emit one long beep, the keypad will
then lock out. In this instance, please switch
the ignition o and then back on again, this
will reset the keypad ready for a correct
code to be entered.
ATTENTION!!!
Factory default code should be changed at time of installation,
please refer to master code setting later in this manual.
CODE DEFINITIONS
Master PIN code: The Skybrake TOUCH keypad comes
supplied with a factory default PIN
code of “0000”. It is important to
change this to a new 4 to 8 digit
unique Master PIN code that only
the owner should know. The Master
PIN code is used to add and delete
up to 5 additional user codes.
User PIN code: With the use of the Master PIN code,
an additional ve access codes can
be added for non owner driver
authorisation. Any of these can be
deleted or changed at any time. A
user code does not have access to
add or delete any authorisation codes.
To Next Page
Loading...
