Skybrake TOUCH - Additional Users Chart; Changing Pin Codes; Re-Setting the Master PIN Code from the Factory Default 0000 PIN Code; Changing the Master PIN Code

5
Override PIN code: In the event of the Master PIN code
being lost or forgotten, the unique
8 digit Override code should be
used to reset the security system.
After the Override code has been
entered, the security system will
delete all PIN codes from memory,
and the Master PIN code will be
reset to the factory default code of
“0000”.
NOTE:
The Override code can be found on the PIN code card, by
scratching o protection layer (see PIN code card).
ADDITIONAL USERS CHART
If more than one user has access to this vehicle, additional
PIN codes can be stored. A total of ve additional user PIN
codes (except master PIN code) can be stored in the system’s
memory (see table).
CHANGING PIN CODES
Re-setting the Master PIN code from the Factory
default ‘0000’ PIN code
In order to change the Factory default PIN code, proceed as
follows:
1. Turn ON the vehicle’s ignition, the keypad backlight and
red LED will illuminate.
2. Enter the Factory PIN code “0000”, and then press #
to conrm it. If the factory PIN code has been entered
correctly, the system will give two short beeps, and the
green LED light illuminates.
3. Within 5 seconds, press and hold # and
*
buttons
together, the keypad emits two short beeps.
4. Enter the new PIN code (4 to 8 digits) and press # to
conrm it.
5. Repeat the new PIN code and press # to conrm it.
6. Enter “0” and press # to conrm it. (“0” is the default
memory location for the master code)
NOTE!!!
If you make a mistake whilst entering the PIN code, turn the
ignition OFF and start again from step1.
If all of the above steps have been followed correctly, the
keypad will emit two short beeps to conrm the new Master
PIN code, turn o then back on the ignition to test new Master
code.
From this moment on, this code is known as the Master PIN
code. Only the Master PIN code has master access level, it can
be used to manage and disarm the security system.
Changing the Master PIN code
If it is necessary to change the Master PIN code, follow the
instructions for “Changing the Factory default PIN code”
above, substituting the factory ‘0000’ PIN for the current
Master PIN code.
If the Master PIN code has been lost or forgotten, then follow
the instructions for “Enter the Overriding PIN code” further on
in this section.
Adding an additional user PIN code
Up to ve additional PIN codes can be stored in the Skybrake
TOUCH keypad. In order to add a new user PIN code, proceed
as follows:
1. Turn the ignition ON
2. Enter existing Master PIN code, and then press # to
conrm it. If the Master PIN code has been entered
correctly, the keypad will emit two short beeps.
3. Within 5 seconds, press and hold # and
*
buttons
together, the keypad emits two short beeps.
4. Enter the new user PIN code (4 to 8 digits), then press #
to conrm it.
5. Repeat the new user PIN code, and then press # to
conrm it.
6. Enter the keypad memory location number 1 to 5 for
this new PIN code, (i.e. this can be number 1 or 2 or 3 or
4 or 5 see PIN code location chart below) and then press
# to conrm it. If all steps are completed correctly, the
keypad will give two short beeps.
From this moment on, the new user PIN code is stored in the
memory. This process can be repeated adding a further 4
more user pin codes.
NOTE:
The location of each user code should be recorded in the
above table, stored codes can be over written. 1 to 5 in the
box above is the memory location for each stored user code.
Keypad
memory slot
User Customer
codes
0 Master PIN code
1 PIN code for User1
2 PIN code for User2
3 PIN code for User3
4 PIN code for User4
5 PIN code for User5