Need help?Do you have a question about the SLE 4000 and is the answer not in the manual?
Lists critical warnings for safe operation to prevent injury or death.
Provides general operational warnings including user training and environmental considerations.
Lists minimum patient monitoring requirements for effective ventilation.
Lists user-adjustable alarms and breath detection thresholds.
Outlines initial preparation steps, including cleaning and hose connection.
Explains turning the ventilator on and off, and mains power indicators.
Details procedures and recommendations for charging backup batteries.
Instructs to carry out ventilator setup before tests.
Details connecting hoses and circuit, ensuring no mains connection.
Guides testing mains power alarms, including fail and disconnect indicators.
Covers testing gas supply by connecting/disconnecting hoses.
Describes performing a high pressure alarm test by constricting the airway.
Confirms oxygen calibration completion and readiness.
Directs to chapter 16 for mode setup.
Provides a checklist of symptoms, causes, and remedies for pre-use test failures.
Explains high/low pressure alarm function, limits, and autotracking.
Explains setting breath detection threshold in flow waveform for interactive modes.
Discusses operating without a flow sensor and setting pressure trigger sensitivity.
Details setting pressure trigger level after patient connection.
Lists essential checks before ventilator setup, including humidifier, circuit, and test lung.
Explains setting O2% in Ventilation Off mode and preview modes.
Guides CPAP mode setup, default parameters, and actions after patient connection.
Guides CMV mode setup, default parameters, and actions after patient connection.
Guides PTV mode setup, default parameters, and actions after patient connection.
Guides PSV mode setup, default parameters, and actions after patient connection.
Guides SIMV mode setup, default parameters, and actions after patient connection.
Guides HFO Only mode setup, default parameters, and actions after patient connection.
Guides HFO+CMV mode setup, default parameters, and actions after patient connection.
Details the procedure for calibrating the flow sensor before circuit insertion.
Provides instructions for cleaning, disinfecting, and sterilizing the flow sensor.
Describes High Pressure alarm, causes, and actions.
Details Low Pressure alarm, causes, and actions.
Explains Breath Not Detected alarm and potential causes like tube blockage/leaks.
Describes Low Tidal Volume alarm and how to adjust the level.
Lists symptoms, causes, and remedies for ventilation problems.
Lists symptoms, causes, and remedies for ventilator issues like screen failures.
Details alarm descriptions and recommended actions.
Lists and categorizes alarms into user-settable and obligatory.
Explains functional testing purpose for safe and consistent ventilator performance.
Guides testing complete power fail alarm triggered by mains/battery failure.
Details flow sensor calibration procedure, including occlusion.
Guides testing High/Low Oxygen alarms by adjusting O2% and verifying triggers.
Tests CPAP parameters, alarms, manual breaths, and Apnoea setup.
Details testing High Pressure alarm by reducing setting and observing gas cut-off.
Guides testing Low Pressure alarm by increasing setting and observing gas cut-off.
Details testing Breath Not Detected alarm by manipulating test lung/flow sensor.
Guides testing Leak/Block alarms by disconnecting/occluding tubing.
Details testing Mains Failure alarm by disconnecting mains power.
Guides testing gas supply alarms by disconnecting supplies.
Details testing Flow Sensor Disconnect alarm by disconnecting sensor plug.
Guides testing Cycle Fail alarm by adjusting thresholds and observing pressure waves.
Tests the functionality of the HFO mode, verifying oscillations and waveforms.
Tests the functionality of HFO+CMV mode, verifying cycles, waveforms, and I:E ratio.
Details testing Pressure Change alarm by disconnecting flow sensor.
Lists critical warnings for safe operation to prevent injury or death.
Provides general operational warnings including user training and environmental considerations.
Lists minimum patient monitoring requirements for effective ventilation.
Lists user-adjustable alarms and breath detection thresholds.
Outlines initial preparation steps, including cleaning and hose connection.
Explains turning the ventilator on and off, and mains power indicators.
Details procedures and recommendations for charging backup batteries.
Instructs to carry out ventilator setup before tests.
Details connecting hoses and circuit, ensuring no mains connection.
Guides testing mains power alarms, including fail and disconnect indicators.
Covers testing gas supply by connecting/disconnecting hoses.
Describes performing a high pressure alarm test by constricting the airway.
Confirms oxygen calibration completion and readiness.
Directs to chapter 16 for mode setup.
Provides a checklist of symptoms, causes, and remedies for pre-use test failures.
Explains high/low pressure alarm function, limits, and autotracking.
Explains setting breath detection threshold in flow waveform for interactive modes.
Discusses operating without a flow sensor and setting pressure trigger sensitivity.
Details setting pressure trigger level after patient connection.
Lists essential checks before ventilator setup, including humidifier, circuit, and test lung.
Explains setting O2% in Ventilation Off mode and preview modes.
Guides CPAP mode setup, default parameters, and actions after patient connection.
Guides CMV mode setup, default parameters, and actions after patient connection.
Guides PTV mode setup, default parameters, and actions after patient connection.
Guides PSV mode setup, default parameters, and actions after patient connection.
Guides SIMV mode setup, default parameters, and actions after patient connection.
Guides HFO Only mode setup, default parameters, and actions after patient connection.
Guides HFO+CMV mode setup, default parameters, and actions after patient connection.
Details the procedure for calibrating the flow sensor before circuit insertion.
Provides instructions for cleaning, disinfecting, and sterilizing the flow sensor.
Describes High Pressure alarm, causes, and actions.
Details Low Pressure alarm, causes, and actions.
Explains Breath Not Detected alarm and potential causes like tube blockage/leaks.
Describes Low Tidal Volume alarm and how to adjust the level.
Lists symptoms, causes, and remedies for ventilation problems.
Lists symptoms, causes, and remedies for ventilator issues like screen failures.
Details alarm descriptions and recommended actions.
Lists and categorizes alarms into user-settable and obligatory.
Explains functional testing purpose for safe and consistent ventilator performance.
Guides testing complete power fail alarm triggered by mains/battery failure.
Details flow sensor calibration procedure, including occlusion.
Guides testing High/Low Oxygen alarms by adjusting O2% and verifying triggers.
Tests CPAP parameters, alarms, manual breaths, and Apnoea setup.
Details testing High Pressure alarm by reducing setting and observing gas cut-off.
Guides testing Low Pressure alarm by increasing setting and observing gas cut-off.
Details testing Breath Not Detected alarm by manipulating test lung/flow sensor.
Guides testing Leak/Block alarms by disconnecting/occluding tubing.
Details testing Mains Failure alarm by disconnecting mains power.
Guides testing gas supply alarms by disconnecting supplies.
Details testing Flow Sensor Disconnect alarm by disconnecting sensor plug.
Guides testing Cycle Fail alarm by adjusting thresholds and observing pressure waves.
Tests the functionality of the HFO mode, verifying oscillations and waveforms.
Tests the functionality of HFO+CMV mode, verifying cycles, waveforms, and I:E ratio.
Details testing Pressure Change alarm by disconnecting flow sensor.
General| Brand | SLE |
|---|---|
| Model | 4000 |
| Category | Medical Equipment |
| Language | English |
To Next Page
