Need help?Do you have a question about the SLE SLE5000 Model J and is the answer not in the manual?
Safety warnings for ventilator operation and maintenance.
Precautions for handling and operating the ventilator safely.
Step-by-step guide to navigate and access calibration programs.
Outlines the four main functions of the calibration program.
Explains calibration of oxygen monitoring and flow systems.
Details accessing and performing touch screen calibration.
Lists electronic and pneumatic components for replacement.
Steps for removing and replacing the ventilator batteries.
Details the electrical safety tests and their expected results.
Lists components for 24 month/10,000 hour and 48 month/20,000 hour overhauls.
Instructions for carrying out the 24 month/10,000 hour overhaul.
Post-overhaul setup steps including calibration and testing.
Instructions for carrying out the 48 month/20,000 hour overhaul.
Lists equipment needed for calibration procedures.
Procedure for calibrating controller and monitor subsystems.
Steps for calibrating the block and leak pressure sensors.
Procedure for zeroing blender pressure sensor and trimming input regulators.
Steps for calibrating the mean jet pressure regulator.
Procedure for calibrating the forward jet pressure regulator.
Steps for calibrating the reverse jet pressure regulator.
Procedure for calibrating the O2 system.
Procedure for soak testing the ventilator after calibration.
Verifying pressure settings and waveforms in various modes.
Test procedure for the complete power fail alarm.
Procedure for calibrating the flow sensor.
Test procedure for the oxygen alarm system.
Testing functions and alarms in CPAP preview mode.
Test procedure for the high pressure alarm.
Test procedure for the low pressure alarm.
Test procedure for the breath not detected alarm.
Test procedures for leak and block alarms.
Test procedure for the mains failure alarm.
Test procedures for gas supply failure alarms (No Air, No O2, No Gas).
Test procedure for the flow sensor disconnect alarm.
Test procedure for the cycle fail alarm.
Testing functions and parameters in HFO mode.
Testing functions and parameters in CMV mode.
Testing functions and parameters in PSV mode.
Testing functions and parameters in SIMV mode.
Testing functions and parameters in HFO+CMV mode.
Test procedure for the pressure change alarm.
Troubleshooting for the symptom of the mains present LED being OFF.
Troubleshooting for a blank ventilator screen with power LED ON.
Procedure for 100% oxygen system calibration.
Procedure for 21% & 100% oxygen system calibration.
Details of user-settable and obligatory alarms.
Verifying pressure settings and waveforms in various modes.
Checks for power fail alarm and FiO2 setting.
Tests for touch screen beep and oxygen alarms.
Tests for various ventilation modes and associated alarms.
Instructions for activating VueLink using an activation code.
Procedure for disabling the VueLink feature.
Safety warnings for ventilator operation and maintenance.
Precautions for handling and operating the ventilator safely.
Step-by-step guide to navigate and access calibration programs.
Outlines the four main functions of the calibration program.
Explains calibration of oxygen monitoring and flow systems.
Details accessing and performing touch screen calibration.
Lists electronic and pneumatic components for replacement.
Steps for removing and replacing the ventilator batteries.
Details the electrical safety tests and their expected results.
Lists components for 24 month/10,000 hour and 48 month/20,000 hour overhauls.
Instructions for carrying out the 24 month/10,000 hour overhaul.
Post-overhaul setup steps including calibration and testing.
Instructions for carrying out the 48 month/20,000 hour overhaul.
Lists equipment needed for calibration procedures.
Procedure for calibrating controller and monitor subsystems.
Steps for calibrating the block and leak pressure sensors.
Procedure for zeroing blender pressure sensor and trimming input regulators.
Steps for calibrating the mean jet pressure regulator.
Procedure for calibrating the forward jet pressure regulator.
Steps for calibrating the reverse jet pressure regulator.
Procedure for calibrating the O2 system.
Procedure for soak testing the ventilator after calibration.
Verifying pressure settings and waveforms in various modes.
Test procedure for the complete power fail alarm.
Procedure for calibrating the flow sensor.
Test procedure for the oxygen alarm system.
Testing functions and alarms in CPAP preview mode.
Test procedure for the high pressure alarm.
Test procedure for the low pressure alarm.
Test procedure for the breath not detected alarm.
Test procedures for leak and block alarms.
Test procedure for the mains failure alarm.
Test procedures for gas supply failure alarms (No Air, No O2, No Gas).
Test procedure for the flow sensor disconnect alarm.
Test procedure for the cycle fail alarm.
Testing functions and parameters in HFO mode.
Testing functions and parameters in CMV mode.
Testing functions and parameters in PSV mode.
Testing functions and parameters in SIMV mode.
Testing functions and parameters in HFO+CMV mode.
Test procedure for the pressure change alarm.
Troubleshooting for the symptom of the mains present LED being OFF.
Troubleshooting for a blank ventilator screen with power LED ON.
Procedure for 100% oxygen system calibration.
Procedure for 21% & 100% oxygen system calibration.
Details of user-settable and obligatory alarms.
Verifying pressure settings and waveforms in various modes.
Checks for power fail alarm and FiO2 setting.
Tests for touch screen beep and oxygen alarms.
Tests for various ventilation modes and associated alarms.
Instructions for activating VueLink using an activation code.
Procedure for disabling the VueLink feature.
General| Brand | SLE |
|---|---|
| Model | SLE5000 Model J |
| Category | Medical Equipment |
| Language | English |
To Next Page
