SLE SLE5000 Model J - 29 Main Loom Circuit Diagram

SLE SLE5000 Model J

344 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

(Model J) Page 223

29. Main Loom Circuit Diagram

Table of Contents

Default Chapter3
- Table of Contents3
1 Warnings and Cautions10
- Warnings10
- Cautions11
2 Principles of Operation14
- Electronic System14
- Pneumatic System15
3 Description of Symbols18
4 Equipment List22
5 Engmode24
- Accessing the Calibration Programs24
- Ventilator Calibration Program26
- O2 & Flow System Calibration27
- Reset Elapsed Time28
- Language Selection28
- Activation of Language Selection Program Form User Interface29
- Exit29
- Touch Screen Calibration Program30
6 Component Replacement Procedure32
7 Preparing the SLE500033
8 Component Replacement (Electronic Unit)35
- N6631/21/CF/50 Compact Flash Card35
- N6631/LX800 PC Board35
- N6634/OEM2 CAN Card36
- N6631/2216 Serial Controller (Touch Screen)36
- L0275/OEM2 Computer/Display Control Assembly37
- A0763/02/M Control/Monitor Board38
- M0915 Power Supply Unit39
- M0901 Batteries40
- A0761 Transducer PCB Assembly41
- N6631/13 Inverter PCB42
- N6631/02 LCD & N6631/05 Touch Screen43
9 Component Replacement (Pneumatic Unit)45
- Duckbill and Conical Filters45
10 A0763/02/M Monitor and Control Board56
- A0763/02/M Board Programmable Devices56
- A0763/02/M Board Hardware Identifier57
11 Electrical Safety Testing of the SLE500061
12 PSU Testing65
13 Ventilator Power up and Power down68
14 Back-Up Battery Charging69
- Battery Indicator69
15 Extended Storage71
16 Maintenance and Overhaul74
- Preventative Maintenance Kit74
- 36 Month Preventative Maintenance Procedure76
- Month and 48 Month Overhaul Procedures84
- Month / 10,000 Hour Overhaul Procedure86
- Month / 20,000 Hour Overhaul Procedure94
- Month Overhaul Procedure Using N9410/48/G Overhaul Kit96
17 Calibration Procedure for V4.3.1 & V4.3.2 Software108
- Equipment Required for Calibration108
- Preliminary Inspection before Calibration109
- Pneumatic Set up110
- Calibration of Controller and Monitor Subsystems113
- Controller "Block and Leak" Pressure Sensor Calibration115
- Controller Blender Pressure Sensor Zeroing and Input Pressure Reg. Trim116
- Mean Jet Pressure Regulator Calibration117
- Forward Jet Pressure Regulator Calibration119
- Reverse Jet Pressure Regulator Calibration120
- Time Constant for Pressure Measurement Waveform121
- Wave Shaping for Leading and Trailing Edge of Insp. Phase121
- O2 System Calibration123
- Flow System Calibration123
- Pressure Triggering Verification123
- Gas Fail Detection Verification123
- Blender and Oxygen Monitoring Verification124
- Soak Test125
- Battery Charge Verification126
- Total Power Fail Alarm Test126
- Pressure Calibration Verification127
18 Functional Testing130
- Ventilator Setup130
19 Trouble Shooting Chart162
20 Software Version History172
- Technical Information173
21 Oxygen Calibration Routines174
- One Point or 100% Oxygen System Calibration174
- Two Point or 21% & 100% Oxygen System Calibration174
22 Alarms176
- Alarm Protocols176
- Alarm Sounds176
- Alarm Descriptions and Actions to be Taken177
- Software and System Fail Protocols196
23 Cleaning, Disinfection and Sterilization197
- Preparation of a New Ventilator197
- Cleaning and Disinfection of an In-Service Ventilator197
- Cleaning Method198
- Disinfection Method199
- Sterilization Method200
24 Technical Specification201
- Operating Modes Conventional Ventilation201
- HFO Ventilation203
- Measurement207
- Exhalation Block Port Jet Sizes208
- Alarms209
- Patient Circuits210
- Outputs211
- Gas Supplies212
- Power, Dimensions, Classification Etc213
- Classification213
- Environmental Storage Conditions213
25 EMC Compliance214
- Electromagnetic Immunity215
- Recommended Separation Distances between Portable and Mobile RF Communications Equipment and the SLE5000217
26 Ventilator Labelling218
27 Electrical Block Diagram220
28 L0280/KV Pneumatic Unit Layout & Schematic221
- Layout221
- Schematic222
29 Main Loom Circuit Diagram223
30 L0275/OEM2 Assembly Schematic224
31 A0761 Circuit Diagram226
- Transducer PCB Assembly226
32 A0763/02 Circuit Diagrams228
- Micro Controller228
- Conventional Valve Drive229
- Power Distribution and Hardware Identifier230
- Analogue Valve Drive / Non Volatile Memory / Interboard Comms231
- High Speed Valve Drive232
- Analogue Data Acquisition/Monitor Port233
- Control & Monitor, PCB PSU Circuit234
- Control & Monitor, Micro Non-Isolated235
- Control & Monitor, Micro Isolated236
- Control & Monitor, Analog Isolated237
- Control & Monitor, Alarm Controller238
33 Illustrated Parts List240
- Ventilator Assembly242
- Base Plate and Side Door Assembly249
- Front Facia Assembly251
- Electronic Module253
- Pneumatic Module273
- DISS Air and Oxygen Fittings285
34 Modifications288
- Equipotential Stud Modification288
- Modification a as Per SI120401 - (Bypassing of Oxygen Volume Chamber)290
- Modification 1, 2 & 4 as Per EMC Upgrade292
- Contents of N9020/000/KIT Kit293
- Equipment List293
- Checking the Modification Status295
- EMC Upgrade Procedure296
- Modification 1 (MOD1)298
- Modification 2 (MOD2)300
- Modification 4 (MOD4)301
- Re-Assembly and Testing302
- MOD Identification302
- Re-Assembly302
Appendix 1. Calibration Checklist305
Appendix 2. Check List313
Appendix 3. TB & si Index318
35 Technical Bulletin & Service Information Letters318
- Service Information Letters318
- Technical Bulletins320
Appendix 4322
- Overview323
- Data and Pinout Description323
- Cable323
- Parameter Descriptions and Format324
- List of Parameters324
- Table of Current Alarm Condition Codes327
- RS232 Connection Settings and Testing Data Output329
- Glossary329
36 Rs232322
- Warnings for RS232322
- Location of RS232 Port322
Appendix 5. Vuelink332
37 Vuelink Technical Data332
- Glossary332
- Connecting the SLE5000 to the Vuelink Patient Monitor332
- Parameter Descriptions333
- Data Transferred to the Vuelink System from the SLE5000334
- Alarm and Inoperative Indications336
- Vuelink Task Window Layout339
- Notes on General System Behaviour340
- Activation of Vuelink341
- Disabling Vuelink342

Related product manuals

Preview: SLE SLE1000

Preview: SLE 5000

Preview: SLE 2000