SMA SUNNY BOY 3600TL User Manual (English)

Other manuals for SMA SUNNY BOY 3600TL

Operating Manual68 pages

Installation Manual120 pages

Quick Reference Guide32 pages

Questions and Answers:

B
Bradley Evans MDAug 27, 2025
Why is my SMA Inverter showing system disturbance (Event 401 to 404)?
- J
  jenniferjonesAug 27, 2025
  If your SMA Inverter is experiencing a system disturbance (Event 401 to 404), the inverter is no longer in grid-parallel operation and has stopped feed-in for safety reasons. Check the grid connection for strong, short-term frequency variations. If there are frequent fluctuations and this error occurs as a result, ask your network operator if it would be acceptable to change the operating parameters. Discuss the proposed parameters with the SMA Service Line.
H
Hannah HoweAug 28, 2025
What does DC overvoltage (Event 3401 to 3402) mean on my SMA Inverter?
- B
  Brenda GarciaAug 28, 2025
  If your SMA Inverter displays a 'DC overvoltage' error (Event 3401 to 3402), it means the DC input voltage connected to the inverter is too high. Disconnect the inverter from the PV array immediately. Check that the DC voltage of the strings is in compliance with the input voltage range of the inverter before reconnecting the inverter to the PV array. If the voltage is within the permissible input voltage range, the inverter may be defective. Contact the SMA Service Line.
C
Crystal HuberAug 28, 2025
Why does my SMA SUNNY BOY 3600TL show unstable operation (Event 3301 to 3303)?
- T
  Tyler JimenezAug 28, 2025
  If your SMA Inverter displays unstable operation (Event 3301 to 3303), it means there is not enough power at the DC input of the inverter for stable operation. Wait until irradiation is higher. If this event recurs at medium irradiation levels, check the PV plant design and the correct circuitry of the PV array.
P
Phillip WangAug 29, 2025
How do I fix overheating (Event 6501 to 6502) on my SMA SUNNY BOY 3600TL?
- L
  Laura ThomasAug 29, 2025
  If your SMA Inverter is showing a self-diagnosis overheating error (Event 6501 to 6502), the inverter interrupts feed-in operation due to interior overheating. Ensure sufficient ventilation and check heat dissipation.
E
ellisonjohnAug 29, 2025
What does it mean when my SMA Inverter reports derating (Event 8001)?
- E
  Elizabeth MackAug 29, 2025
  If your SMA Inverter shows that derating occurred (Event 8001), it means the power supplied by the inverter has been reduced to below nominal power for more than 10 minutes due to overheating. If this event occurs frequently, ensure sufficient ventilation and check heat dissipation.
E
Erica FaulknerAug 30, 2025
What causes high discharge current (Event 3601) on my SMA Inverter?
- A
  adamnicholsAug 30, 2025
  If your SMA Inverter displays 'High discharge curr.' (Event 3601), the leakage current from the inverter and the PV array is too high. Check strings for earth faults. The installer of the PV array must remedy any earth faults before the affected string is reconnected.
J
Joseph LambertAug 30, 2025
What does insulation resistance (Event 3501) mean on SMA Inverter?
- R
  robinsonjasonAug 30, 2025
  If your SMA Inverter displays 'Insulation resist.' (Event 3501), the inverter has detected an earth fault in the PV array. Check strings for earth faults. The installer of the PV array must remedy any earth faults before the affected string is reconnected.
A
Aaron SmithAug 31, 2025
Why is the residual current too high (Event 3701) on my SMA Inverter?
- S
  Stephanie EllisonAug 31, 2025
  If your SMA Inverter displays 'Resid.curr.too.high' (Event 3701), the inverter has detected residual current. Check strings for earth faults. The installer of the PV array must remedy any earth faults before the affected string is reconnected.
E
Edwin FitzgeraldAug 31, 2025
What to do if my SMA Inverter shows DC overcurrent (Event 3801 to 3802)?
- M
  mramirezAug 31, 2025
  If your SMA Inverter is showing a 'DC overcurrent' error (Event 3801 to 3802), the inverter switches off due to an overcurrent on the DC side. If this event occurs frequently, check the design and the circuitry of the PV array.
K
Kevin MitchellAug 31, 2025
Why is my SMA SUNNY BOY 3600TL Inverter waiting for DC start conditions (Event 3901 to 3902)?
- R
  Raymond SmithSep 1, 2025
  If your SMA Inverter displays 'Waiting for DC start conditions' (Event 3901 to 3902), the input power or voltage of the PV modules is not yet sufficient for feeding into the electricity grid. Wait until irradiation is higher. If this event recurs at medium irradiation levels, check the PV plant design and the correct circuitry of the PV array.

SMA SUNNY BOY 3600TL Specifications

General

Rated Output Power	3600 W
Max. input voltage	600 V
Number of MPP Trackers	1
Max. apparent AC power	3600 VA
Nominal AC voltage	230 V
Protection Class	IP65
Operating Temperature Range	-25 °C to +60 °C
AC Voltage Range	184 V - 276 V
Frequency Range	50 Hz / 60 Hz
Cooling	Convection