PARTS WASHER OPERATION
Your SmartWasher
®
is almost ready to use. (The OzzyMat
™
, support grid and
false bottom of the sink are packed inside the sink). Visually inspect for damage
(minor scratches and scuffs are normal due to the molding process).
The SmartWasher
®
will weigh approximately 350/380 pounds (160/174 kg)
when it is filled with fluid. It should be installed close enough to a normal
115VAC (220VAC) ground fault circuit interrupter (GFCI) electrical outlet so
that it can be plugged in. The SmartWasher should be the only item plugged
into this circuit.
DO NOT PLUG IN BEFORE ADDING
FLUID.
Adjust the valve at the base of the nozzle to control the flow
of the fluid through the nozzle. The valve at the base of the
brush hose controls the flow of fluid through the brush. Both
outlets can be operated independently or together.
2.
1.
The pump switch is attached to a ten minute timer. Turning the
switch ON (upward position) will start fluid flowing for ten
minutes. To restart the flow, turn the switch OFF then ON
again and the flow will restart for another ten minutes.
INSTALLATION AND SETUP
The OzzyMat traps sludge and dirt as small as 50 microns. It works
effectively even when it appears dirty. At some point, however, it will
become saturated and unable to pass fluid freely and should be changed.
The FL-4 Multi-layer OzzyMat allows you the benefit of being able to peel
layers between mat changes.
OzzyMat FL-4 Maintenance
Make sure the pump is not running.
1.
Remove the False Bottom from the
sink.
2.
3.
Peel away the top layer of the
OzzyMat and wring out any excess
fluid. Then, dispose of this layer
according to your local regulations.
4.
Return the False Bottom to its proper
place.
OzzyMat
™
Change the OzzyMat every 30 days or once a
month to maintain cleaning performance.
You may be able to dispose of your used OzzyMat as solid waste or with your other absorbent mats.
CHECK LOCAL REGULATIONS:
ChemFree Technical Support : 770-564-5580 www.chemfree.com
ENGLISH
Change The OzzyMat Every 30 Days To Maintain Cleaning Performance
Remove the false bottom and check to make
sure the mat support grid is in the bottom of the
sink. Remove and discard packing material.
REPLACING THE OZZYMAT
Make sure the pump is not running.
1.
Remove the False Bottom from the sink.
2.
Remove the last layer of the soiled OzzyMat and set to one side
of the filter support grid.
3.
Remove a new OzzyMat from its poly bag, unfold the mat and lay
it on top of the filter support grid - white side up.
4.
Wring any excess fluid from the old mat onto the new OzzyMat. It
is important to wring used OzzyMat prior to disposal.
5.
Take the old, used OzzyMat and place into the poly bag the new
mat came in.
6.
7.
Return the False Bottom to its proper position.
Discard used OzzyMat in accordance with your local regulations.
8.
Maintain the performance and effectiveness of the
OzzyJuice by changing the OzzyMat EVERY 30 DAYS.
1
CHANGE THE OZZYMAT
the OzzyMat
®
needs to
be replaced every 30
days or once a month
to maintain cleaning
performance.
PARTS WASHER SETUP
Place the false bottom in position in the sink.
2.
Remove the OzzyMat
™
from its package, unfold it and lay it
on the mat support grid located in the lowest level in the
sink. Make sure to lay the OzzyMat white side up.
1.
Form the flexible nozzle to its desired shape and be sure
that the parts brush is inside the sink.
3.
At start up, carefully add 25 gallons (five) 5-gallon
containers) of OzzyJuice
®
to the SmartWasher by slowly
pouring the solution directly into the sink.
5.
Plug the unit into a 115V (220VAC) GFCI electrical outlet.
6.
The SmartWasher will take approximately four hours to
heat up to its selected optimal temperature of 105°F (+-2°)
(40°C)(+-1°) OR 115° F(+-2°) (46°C)(+-1°). This
temperature will be maintained as long as the
SmartWasher is plugged in and full of OzzyJuice. (If the
Add Fluid Light is on, the heater automatically shuts off.)
7.
4.
DO NOT PLUG UNIT IN BEFORE ADDING
OZZYJUICE.
r
®
SmartWashe
Ozzy
®
To Next Page
Loading...