14
Pressure response with no load is approx. 0.1 sec.
High-Speed Response Time Specifications
7
ITV X154
Pressure range
2 0 10
1
3
5
0.1 MPa
0.5 MPa
0.9 MPa
S01 2
Pressure display unit
High-speed
response time
specifications
–
2
3
4
5
MPa
kgf/cm
2
bar
PSI
kPa
Input signal
0
1
2
3
Current 4 to 20 mA (Sink type)
Current 0 to 20 mA (Sink type)
Voltage 0 to 5 VDC
Voltage 0 to 10 VDC
Cable connector type
S
L
N
Straight type 3 m
Right angle type 3 m
Without cable connector
Bracket
–
B
C
Without bracket
Flat bracket
L-bracket
Monitor output
1
2
3
Analogue output 1 to 5V DC
Switch output/NPN output
Switch output/PNP output
Thread type
–
N
T
F
Rc
NPT
NPTF
G
Port size
Power supply
voltage
0
1
24 VDC
12 to 15 VDC
Model
1
2
1000 type
2000 type
02
03
OUT port size
2 through 8 station manifold.
How to Order Manifolds
IITV20 02 5
ITV1000, 2000
Connection thread type
Manifold Specifications (Except Series ITV3000)
6
1/4
3/8
–
N
F
PT
NPT
PF
2
8
Valve stations
2 stations
8 stations
How to Order Manifold Assemblies
Example
Note) Refer to the table below for possible mixed combination.
Made to Order Specifications
Series
ITV1000/2000/3000
Contact SMC regarding detailed dimensions, specifications and delivery times.
Made to
Order
Model
ITV101
씲
ITV103
씲
ITV105
씲
ITV201
씲
ITV203
씲
ITV205
씲
ITV101
씲
ITV103
씲
ITV105
씲
ITV201
씲
ITV203
씲
ITV205
씲
1
2
3
1/8 (1000 type)
1/4 (1000, 2000 type)
3/8 (2000 type)
1
2
3
Note 1)
IITV20-02-3
Manifold base
(3 stations)
P398020-13
Blanking plate assembly
ITV1030-311S-X153
Electro-pneumatic regulator
ITV2050-212S-X153
Electro-pneumatic regulator
P
S
U
P
2
G
MPa
L
O
C
K
U
N
L
O
C
K
R
E
S
E
T
SET
E
SM
C
R
E
G
UL
A
T
O
R
2
O
U
T
G
P
MPa
L
O
C
K
U
N
L
O
C
K
R
E
S
E
T
SET
E
S
M
C
R
E
G
U
LA
T
O
R
Stations
Note 1) Electro-pneumatic regulators are counted starting from station 1 on
the left side with the OUT ports in front.
Note 2) The port size for mounted electro-pneumatic regulators is Rc1/8
(ITV1000), Rc1/4 (ITV2000) only.
Note 3) When there is a large number of stations, use piping with the largest
possible inside diameter for the supply side, such as steel piping.
Note 4) The use of the straight type cable connector is recommended.
To mount right angle type, be certain to check that no possible
interference occurs.
Note 5) When mounting a blanking plate and the regulator with different
pressure set, please inform SMC of the order of a manifold station
beside a purchase order.
IITV20-02-3 ……………………
∗ITV2030-311S-X153 ………
.
∗P398020-13 …………………
∗ITV2050-212S-X153 ………
.
1 set (3 station manifold base part no.)
1 set (Electro-pneumatic regulator part no.)
Note 2)
1 set (Blanking plate assembly part no.)
1 set (Electro-pneumatic regulator part no.)
Note 2)
The ∗ is the symbol for mounting. Add the ∗ symbol at the
beginning of part numbers for electro-pneumatic regulators, etc. to
be mounted on the base.
To Next Page
Loading...
Need help?
General
