Why is fabric conditioner not dispensing correctly in my Smeg Washer/Dryer?
If your Smeg Washer/Dryer isn't using all the fabric conditioner or too much water is left in the compartment, check that the detergent drawer siphons are correctly fitted and not clogged.
Why is laundry not properly spun in my Smeg LSTA127?
If your Smeg Washer/Dryer laundry is not properly spun, it could be because large items are screwed up and not evenly distributed within the drum. Always wash a mix of large and small items.
Why is there no water visible in the drum of my Smeg LSTA127?
The water level is below the level of the glass in the door because new Smeg Washer/Dryer appliances use very little water to achieve the same washing and rinsing results.
What to do if water is not pumped out after the last rinse in delicate fabrics and wool wash programmes in Smeg LSTA127?
It is not a malfunction of your Smeg Washer/Dryer: the pause is programmed into washing programme to prevent creasing of fabrics. To pump out water, proceed as described in "Programme End" point.
Critical safety guidelines for installation, use, and general operation of the appliance.
Essential safety measures for electrical connections, earthing, and plumbing.
Prohibits use in hazardous environments, extreme temperatures, or with incorrect hoses.
Covers door safety, handling hot water, child safety, and specific drying risks.
Guidance on placing and ensuring the appliance is level for optimal operation.
Instructions for connecting the appliance to the cold and hot water supply.
Detailed steps for correctly connecting the drain hose to ensure proper drainage.
Essential guidelines for safely connecting the appliance to the electrical power supply.
Explanation of the display, buttons, and programme selector on the appliance's front panel.
Guidance on sorting laundry, understanding care labels, and pre-treating stains.
Instructions on how to load laundry correctly and maximum load capacities.
Guide on using the detergent drawer, types of detergent, and water hardness.
Basic requirements and limitations for drying, including suitable fabrics and load sizes.
A table listing common problems, their potential causes, and checks to perform.
Explains error codes displayed on the appliance and their corresponding solutions.
General| Door hinge | Left |
|---|---|
| Drum volume | 52 L |
| Control type | Buttons, Rotary |
| Loading type | Front-load |
| Tub material | Polypropylene |
| Drum material | Stainless steel |
| Product color | White |
| Built-in display | Yes |
| Appliance placement | Built-in |
| Door panel included | No |
| Drying capacity | 4 kg |
| Washing capacity | 7 kg |
| Delay start (max) | 24 h |
| Spin-drying class | - |
| Maximum spin speed | 1200 RPM |
| Minimum spin speed | 500 RPM |
| Noise level (spin) | 70 dB |
| Noise level (wash) | 56 dB |
| Noise level (drying) | 58 dB |
| Number of drying programs | 2 |
| Number of washing programs | 12 |
| Cycle time washing & drying | 365 min |
| Washing class | A |
| Annual water consumption washing & drying | 18000 L |
| Annual energy consumption washing & drying | 970 kWh |
| Door opening angle | 110 ° |
| Connected load | 2000 W |
| Water consumption washing per cycle | 47 L |
| Energy consumption washing per cycle | 1.02 kWh |
| Water consumption washing & drying per cycle | 90 L |
| Energy consumption washing & drying per cycle | 4.85 kWh |
Weight and Dimensions| Depth | 560 mm |
|---|---|
| Width | 596 mm |
| Height | 820 mm |
| Door opening diameter | 300 mm |
| Installation compartment depth | 584 mm |
| Installation compartment width | 600 mm |
To Next Page
