Smeg WDF7512 User Manual (English)

Questions and Answers:

E
Elizabeth SteinAug 14, 2025
Why my Smeg WDF7512 will not start?
- C
  Corey PetersonAug 14, 2025
  If your Smeg Washer/Dryer won't start, there are several potential causes: * It might not be plugged in. In this case, insert the plug into the socket. * The fuse could be faulty, requiring a replacement. * The mains supply might be cut off, so check the mains supply. * You may not have pressed the Start/Pause button; press it to start. * The program dial might be in the Stop (off) position; turn it to the desired position. * The door might not be closed properly; ensure the door is fully closed.
M
Michael UnderwoodAug 17, 2025
Why is my Smeg WDF7512 Washer/Dryer vibrating?
- D
  dominicyorkAug 17, 2025
  If your Smeg Washer/Dryer vibrates, it could be due to several reasons: * The feet may not be adjusted properly; adjust the feet. * The transit bolts might not have been removed; remove the transit bolts. * The machine might have only a small amount of laundry inside. Note that this should not prevent the operation of your machine. * The machine could be overloaded, or the laundry may not be distributed evenly; avoid overloading and ensure the laundry is spread out. * The machine may be located on a hard surface; avoid installing it on hard surfaces and leave a 2 cm gap between walls or hard surfaces.
M
martinezalexisAug 21, 2025
What to do if my Smeg Washer/Dryer does not discharge?
- J
  Johnny OwensAug 21, 2025
  If your Smeg Washer/Dryer isn't discharging water, it might be because the drain hose is clogged or twisted. Check the drain hose to resolve this. Alternatively, the pump filter could be clogged, so clean the pump filter.
C
christopher65Aug 25, 2025
How to stop excessive foam in Smeg Washer/Dryer detergent drawer?
- B
  Brianna LaneAug 25, 2025
  If there's excessive foam in the detergent drawer of your Smeg Washer/Dryer, it's likely due to: * Using too much detergent. Press the Start/Pause button. To stop the foam, dilute one tablespoon of softener into 1/2 litre of water and pour into the detergent drawer. Press the Start/Pause button after 5-10 mins. * Using the wrong detergent. Ensure you only use detergents specifically produced for automatic washing machines.
K
Kurt MathisAug 27, 2025
Why is there detergent residue on laundry after washing in Smeg WDF7512 Washer/Dryer?
- D
  davisalexanderAug 27, 2025
  If you notice detergent residue on your laundry after washing in your Smeg Washer/Dryer: * Non-dissolving particles of some detergents may appear as white spots. In this case, perform an extra rinse, or clean your laundry with a brush after it dries. * There is untreated oil, cream or laundry. Use the amount of detergent as instructed on the packaging in the next wash.
D
David SmithAug 30, 2025
Why spinning operation is not performed in Smeg Washer/Dryer?
- Y
  ypowellAug 30, 2025
  If the spinning operation is not performed or runs late on your Smeg Washer/Dryer, it may be because the Unbalanced load control system has been activated. This is not a fault. The system will try to spread your laundry evenly, and the spinning will begin once the load is balanced. Place the laundry in the machine in a balanced fashion next time.
J
Janice OrtizSep 3, 2025
Why is laundry still damp after drying in Smeg WDF7512?
- B
  Brittney BoydSep 3, 2025
  If laundry remains damp after drying in your Smeg Washer/Dryer, it could be that the appropriate drying program was not selected, or the maximum load capacity for the selected program might have been exceeded. Select a drying programme appropriate for your laundry.
D
Dr. Ryan FitzgeraldSep 6, 2025
Why is my Smeg Washer/Dryer washing result unsatisfactory?
- K
  kevinflemingSep 6, 2025
  If the washing result with your Smeg Washer/Dryer is unsatisfactory, consider the following: * The laundry might be too dirty for the selected program. Select programs appropriate for your laundry’s level of dirtiness. * Not enough detergent might have been used. Use the amount of detergent as instructed on the packaging. * There might be too much laundry in your machine. Check that the maximum capacity of your Washer Dryer is not exceeded.
K
Kayla ShepardSep 10, 2025
What to do if Smeg Washer/Dryer discharges water immediately after loading?
- J
  Jermaine LevySep 10, 2025
  If your Smeg Washer/Dryer discharges water as soon as it's loaded, it's likely because the end of the water drain hose is too low. Set the water drain hose to an appropriate height to resolve this.