Smiths Medical CADD-Legacy PCA - User Manual

Smiths Medical ASD, Inc.
6000 Nathan Lane North
Minneapolis, MN 55442, USA
Tel: 1-614-210-7300
Toll-Free USA: 1-800-258-5361
www.smiths-medical.com
Product(s) described may not be licensed or available for sale in Canada
or other countries outside of the United States.
CADD, CADD-Legacy, the Medication Cassette Reservoir and the Smiths Medical
design mark are trademarks of Smiths Medical. The symbol ® indicates the
trademark is registered in the U.S. Patent and Trademark Office and certain other
countries. ©2017 Smiths Medical. All rights reserved. IN19882EN-112017
A. Display shows
programming information
and messages
B. Power Jack used to plug in
AC Adapter
C. Accessory Jack used to
plug in Remote Dose Cord
D. Indicator Light indicates
AC power in use
E. Air Detector
F. Cassette (part of reservoir
or administration set that
attaches to pump)
G. Threaded Mounting Hole
for use with Polemount
Bracket Adapter (back of
pump)
H. Battery Compartment
(back of pump)
I. Cassette Latch attaches
cassette to pump (side of
pump)
CADD-Legacy
®
PCA
Infusion Pump Model 6300
Quick Reference Card for Clinicians Lock Level 0 (LL0)
For more information, please visit
www.smiths-medical.com
G
H
I
A
B
C
E
D
F
Read the entire Operator’s Manual before operating the CADD-Legacy
®
ambulatory
infusion pump. Failure to properly follow warnings, cautions and instructions could
result in death or serious injury to the patient. Please see the instructions for use for
a complete listing of the indications contraindications, warnings and precautions.
Warning: This Quick Reference Card should be used by clinicians only. Do not permit
patients to have access to this card, as the information would allow access to all
programming and operating functions. Assistance with the CADD-Legacy
®
PCA pump
is available to clinicians by calling 1-800-258-5361.
IN19882EN-112017.indd 1 11/01/18 11:49

Summary

Device Overview

Pump Component Identification

Identifies key external components of the CADD-Legacy PCA pump, including display, buttons, ports, and cassette attachment points.

Pump Programming - Initial Setup

Reservoir Volume, Units, and Concentration

Guides through setting Reservoir Volume, Units, and Concentration for pump programming.

Dosing Parameters: Rate, Demand, Lockout

Details setting Continuous Rate, Demand Dose, and Dose Lockout time.

Pump Programming - Advanced Setup

Dose Counts and Verification

Covers setting Doses Per Hour, clearing recorded doses, verifying sensors, and adjusting lock levels.

Pump Operations - Core Functions

Lock Level, Start;Stop, and Priming

Instructions for changing lock level, starting, stopping, priming, and resetting reservoir volume.

Power and Battery Management

Procedures for turning the pump on/off and changing the batteries.

Pump Operations - Advanced Features

Biomed Functions and Sensor Settings

Accessing and configuring Biomed Functions, including Air Detector and Upstream Sensor settings.

Pump Operations - Cassette Handling

Cassette Attachment and Removal

Step-by-step guide for removing a used cassette and attaching a new one to the pump.

Programming and Keypad Reference

Programming Screen Definitions

Explains the purpose of various screens displayed during pump programming.

Keypad Button Functions

Describes the function of each button on the CADD-Legacy PCA pump keypad.

Dosing and Remote Control

Initiating Dosing and Bolus Delivery

Instructions for starting a demand dose, a clinician bolus, and using the remote dose cord.

Alarms and Troubleshooting - Initial Alarms

Low Volume and Battery Alarms

Details alarms like Reservoir Volume Low/Empty and Low Battery, with troubleshooting steps.

Alarms and Troubleshooting - System Issues

Pump Status and Occlusion Alarms

Explains alarms related to battery depletion, pump operation, high pressure, and upstream occlusions.

Cassette, Air, and Programming Alarms

Covers alarms for cassette alignment, air in line, stopped pump, and incomplete programming.

Alarms and Troubleshooting - Error Conditions

Error, Service, and Display Issues

Describes alarms for value not saved, general errors, no message display, and service due notifications.

Smiths Medical CADD-Legacy PCA Specifications