Snell K.5mk2 - SPECIFICATIONS

Specifications
Frequency Response (
±
3dB)
Recommended Amplifier Power
Nominal Impedance
Sensitivity [1 watt (2.83v) at 1m]
Tweeter (video-shielded)
Bass Unit (video-shielded)
Placement Switch Positions
Cabinet Construction
Platform Baffle Construction
Grille
Dimensions (HxWxD)
Weight/each
Finish
2
SPECIFICATIONS
E.5mk2 Tower
37-20,000Hz
20-250 watts
4 ohms
90dB
Front-firing: 1-inch (25mm)
black-anodized aluminum
dome with neodymium magnet
structure and multi-finned
aluminum heatsink
Rear-firing: 1-inch (25mm) soft
dome
Dual 6
1
⁄
2
-inch (165mm) bass
units. Variably progressive spi-
der and aluminum shorting
cylinder permit high output
without increased distortion.
Copolymer cones and butyl
rubber surrounds resist envi-
ronmental extremes.
Normal and Boundary
3
⁄
4
-inch MDF walls, I-beam
internal bracing
Exposed layer:
3
⁄
4
-inch high-
density fiberboard
Damping layer: 1.5mm
neoprene
Inner layer:
3
⁄
4
-inch medium-
density fiberboard
Custom-perforated (51% open)
cold-rolled steel, powder-coat
finish
42
3
⁄
8
x 8
1
⁄
2
x 11
1
⁄
2
"
108 x 22 x 29cm
46 lbs (21kg)
Hand-sanded, hand-oiled
Cherry veneer, or hand-painted
Black on American Oak veneer
K.5mk2 Monitor
48-20,000Hz
50-250 watts
8 ohms
86dB
1-inch (25mm) black-anodized
aluminum dome with
neodymium magnet structure
and multi-finned aluminum
heatsink
6
1
⁄
2
-inch (165mm) bass unit.
Variably progressive spider and
aluminum shorting cylinder
permit high output without
increased distortion. Copolymer
cone and butyl rubber surround
resist environmental extremes.
Normal and Boundary
3
⁄
4
-inch MDF walls, I-beam
internal bracing
Exposed layer:
3
⁄
4
-inch high-
density fiberboard
Damping layer: 1.5mm
neoprene
Inner layer:
3
⁄
4
-inch medium-
density fiberboard
Custom-perforated (51% open)
cold-rolled steel, powder-coat
finish
18 x 8
1
⁄
2
x 12"
46 x 22 x 30cm
26 lbs (11.4kg)
Hand-sanded, hand-oiled
Cherry veneer, or hand-painted
Black on American Oak veneer
CR.5mk2 Center Channel
70-20,000Hz
50-200 watts
8 ohms
89dB
1-inch (25mm) black-anodized
aluminum dome with
neodymium magnet structure
and multi-finned aluminum
heatsink
Dual 5
1
⁄
4
-inch (135mm) cast-
aluminum baskets. Copolymer
cone and butyl rubber surround
resist environmental extremes.
Normal and Boundary
3
⁄
4
-inch MDF walls, I-beam
internal bracing
Exposed layer:
3
⁄
4
-inch high-
density fiberboard
Damping layer: 1.5mm
neoprene
Inner layer:
3
⁄
4
-inch medium-
density fiberboard
Custom-perforated (51% open)
cold-rolled steel, powder-coat
finish
6
5
⁄
8
x 17 x 9
9
⁄
16
"
16 x 43 x 24cm
17 lbs (7.7kg)
Hand-sanded, hand-painted
Black on American Oak veneer