1. S t a r t
All fans produced by SODECA, hereinafter the manufacturer, and the full line of accessories, have been manufactured in
accordance with the strictest standards in relation toquality assurance, systems and production processes.
T h e i r p r o j e c t , t e s t i n g , m a n u f a c t u r e a n d c o n t r o l s t r u c t u r e h a s b e e n c o n f i g u r e d i n l i n e w i t h E U s t a n d a r d s a n d r e g u l a t i o n s ,
especially in reference to current safety standards.
T h e m a t e r i a l s u s e d i n o u r f a n s , a n d t h e s t a n d a r d i s e d c o m p o n e n t s o f w h i c h t h e y a r e m a d e m e e t t h e s a m e s t a n d a r d s a n d ,
w h e n s o r e q u i r e d , a r e b a c k e d u p b y t h e c o r r e s p o n d i n g q u a l i t y c e r t i f i c a t e s .
T h e O r i g i n a l M a n u a l w a s w r i t t e n i n S p a n i s h .
T h e m a n u f a c t u r e r r e s e r v e s t h e r i g h t t o m a k e m o d i f i c a t i o n s w i t h o u t p r i o r n o t i c e .
All the documentation in this manual is the property of the manufacturer, and its total or partial reproduction is prohibited.
2. P r o d u c t D e f i n i t i o n
H C : Wall-mounted axial fans, with fibreglass-reinforced plastic impellerandIP-55 motor.
H C / A T E X : ATEX-certified. wall-mounted axial extractor fans and optional Ex e. Ex d. Ex tc and Ex tb marking.
IMPORTANT:
T h i s p r o d u c t i s n o t s u i t a b l e f o r u s e i n e x p l o s i v e e n v i r o n m e n t s o r f o r f i r e s a f e t y . (HC)
• T h i s p r o d u c t i s n o t s u i t a b l e f o r fire safety. (HC/ATEX)
3. Generalinformation
• Always check the products received.
• After unpacking the equipment, it must be checked to make sure that it is not damaged. D a m a g e d p r o d u c t s m u s t
never be installed.
• T h i s e q u i p m e n t m u s t n o t b e u s e d f o r p u r p o s e s o t h e r t h a n t h o s e f o r w h i c h i t w a s d e s i g n e d ; i t m u s t o n l y o p e r a t e
under the conditions described in this manual.
• In the event of a defect or malfunction, this must be reported to the authorised representative, with a description of
the problem, in order to coordinate its return or possible repair.
• Before starting up the equipment make sure you have read the safety and installation instructions set out in this
document and the“General Specifications for ATEX Fans”attached to the product documentation.(HC/ATEX)
4. Transportation, storage and handling
• Always hold the equipment at the points provided for this. Do not lift it by the electrical cables, connection boxes,
or the air inlet or outlet.
• Before installation, store the equipment in a clean, dry place, protected from inclement weather.
5. S a f e t y
• D o n o t d i s a s s e m b l e o r m o d i f y t h e e q u i p m e n t . T h i s c o u l d n e g a t i v e l y a f f e c t t h e e q u i p m e n t o r e v e n c a u s e a c c i d e n t s .
• D o n o t p u t y o u r f i n g e r s o r a n y o b j e c t s i n t o t h e p r o t e c t i v e g r i l l e s o n d u c t s , i n l e t s o r o u t l e t s . I f t h i s w e r e t o o c c u r ,
immediately disconnect the equipment's power supply.
• N e v e r u s e a d a m a g e d p o w e r c a b l e .
• D o n o t o p e r a t e t h e e q u i p m e n t i f i t h a s b e e n f o r c i b l y installed on a curved or unstable surface.
• D o n o t p e r f o r m e q u i p m e n t i n s p e c t i o n o r m a i n t e n a n c e w i t h o u t f i r s t c h e c k i n g t h e f o l l o w i n g :
o T h a t t h e e q u i p m e n t h a s b e e n d i s c o n n e c t e d f r o m t h e e l e c t r i c a l s u p p l y .
o T h a t a l l i t s c o m p o n e n t s a r e a t r e s t .
• T h e e q u i p m e n t m u s t n o t b e o p e r a t e d u n l e s s i t h a s b e e n p r o p e r l y i n s t a l l e d a n d t h e i n l e t s a n d o u t l e t s h a v e b e e n
protected, if necessary.
In designing and manufacturing the various Series of t h e m a n u f a c t u r e r ' s Fans and Extractors, Hazard Elimination has been
taken into account, in order to meet the conditions for Integrated Safety.
When their configuration and manufacturing processes permit this, the manufacturer directly incorporates the most appro-
priate Safety Devices. If the conditions for installation or use mean that these devices cannot be incorporated at source, all
additional safety accessories are available for implementation when the equipment is installed and before it is put into ser-
vice.
To Next Page
Loading...
