Sofarsolar SOFAR 3000TL-G3

Questions and Answers

D
Daniel WardAug 18, 2025
What to do if Sofarsolar Inverter shows power grid voltage too high?
- B
  Bruce TranAug 18, 2025
  If the alarm occurs occasionally, the issue might be temporary grid fluctuations; the inverter should return to normal when the grid stabilizes. However, if this happens frequently, verify that your grid voltage and frequency are within the acceptable range. If they are not, contact technical support. If the voltage and frequency are normal, inspect the AC circuit breaker and AC wiring. If problems persist despite correct voltage/frequency and wiring, contact technical support to adjust the inverter's protection settings after getting approval from your local grid operator.
S
shillAug 20, 2025
What to do if Sofarsolar SOFAR 3000TL-G3 shows GFCI fault?
- W
  Wendy ChambersAug 20, 2025
  If the GFCI fault occurs occasionally, it might be due to temporary external circuit abnormalities, and the inverter should automatically return to normal once the issue is resolved. However, if the fault occurs frequently and lasts a long time, check the insulation resistance between the PV array and earth (ground) to ensure it is not too low. Also, inspect the insulation of the PV cables.
R
Rick Evans MDAug 23, 2025
Why is my Sofarsolar SOFAR 3000TL-G3 Inverter temp too high?
- J
  Joseph HarrisAug 23, 2025
  The inverter temperature might be too high because the ambient temperature of its installation location exceeds the upper limit. To resolve this, improve ventilation around the inverter to decrease the temperature.
C
Christina GonzalezAug 26, 2025
What to do if Sofarsolar SOFAR 3000TL-G3 showing input voltage too high?
- M
  Michael LongAug 26, 2025
  The input voltage might be too high because too many PV modules are connected in series in a PV string, causing the voltage (Voc) of the PV string to exceed the inverter's maximum input voltage. To fix this, adjust the number of PV modules connected in series to decrease the voltage of the PV string, ensuring it fits within the inverter's input voltage range. The inverter should automatically return to normal operation after these adjustments.
J
Joshua GonzalezAug 28, 2025
Why Sofarsolar SOFAR 3000TL-G3 showing input voltage too low?
- X
  xtaylorAug 28, 2025
  The input voltage might be too low because too few PV modules are connected in series in a PV string. This results in the voltage (Vmp) of the PV string being lower than the inverter's minimum operating voltage. To resolve this, adjust the number of series-connected PV modules to increase the voltage of the PV string, ensuring it fits within the inverter's input voltage range. The inverter will automatically return to normal operation after the correct adjustments.
J
Jacob MaloneAug 30, 2025
What to do if Sofarsolar SOFAR 3000TL-G3 grid current is too high and hardware protection activated?
- P
  Paul AndersonAug 30, 2025
  ID15-ID24 indicate internal faults within the inverter. Turn OFF the DC switch, wait for 5 minutes, and then turn it back ON. Check if the fault is rectified. If the issue persists, contact technical support.
B
Brian GonzalezSep 2, 2025
Why Sofarsolar SOFAR 3000TL-G3 Inverter derated because of high temperature?
- F
  Franklin JohnsonSep 2, 2025
  The inverter may have derated because the ambient temperature of its installation position exceeds the upper limit. To solve this, improve ventilation to decrease the temperature around the inverter.
R
ramseykristieSep 4, 2025
What to do if Sofarsolar SOFAR 3000TL-G3 Inverter input current is too high?
- A
  Anthony LeeSep 4, 2025
  Check if the input current exceeds the maximum input current of the inverter. Also, verify the input wiring. If both are correct and the issue persists, contact technical support.
J
Jordan GarciaSep 7, 2025
Why Sofarsolar SOFAR 3000TL-G3 bus voltage is too low?
- V
  vgillSep 7, 2025
  If the PV array configuration is correct (no ID05 fault), the bus voltage might be too low because the solar irradiance is insufficient. The inverter should automatically return to normal operation once the solar irradiance returns to a normal level.
C
Charles FritzSep 9, 2025
What to do if Sofarsolar SOFAR 3000TL-G3 Inverter input current is not balanced?
- S
  Stephen RobbinsSep 9, 2025
  Check the input mode setting (parallel mode/independent mode) of the inverter. If it’s incorrect, change it according to the manual.