35
DAB1 DISTRIBUTED AUDIO SYSTEM
4) The DAB1 is factory-programmed for the following keypad functions:
•• PP
RR EESS SS
aannyy SS
OOUU RR CC EE
BBuuttttoonn::
Turns the local zone ON with that source.
•• PP
RR EESS SS
--AA
NN DD
--HH
OOLL DD
aannyy SS
OOUU RR CC EE
BBuuttttoonn::
Activates PARTY MODE with that source for all zones.
•• PP
RR EESS SS
tthhee VV
OOLL UU MM EE
UUPP//DDOOWWNN BBuuttttoonnss::
Raise and lower the volume in the local zone.
•• PP
RR EESS SS
tthhee MM
UU TTEE
BBuuttttoonn ((CC44663300 SSEE MM aaiinn KKeeyyppaadd));; PP
RR EESS SS
tthhee cceenntteerr ooff tthhee VVoolluummee UUPP//DDOOWWNN bbuuttttoonn ((DDAABB11
KKeeyyppaadd))::
Mutes/un-Mute the local zone.
•• PP
RR EESS SS
--AA
NN DD
--HH
OOLL DD
tthhee MM
UU TTEE
BBuuttttoonn ((CC44663300 SSEE MM aaiinn KKeeyyppaadd));; PP
RR EESS SS
--
AANNDD
--HH
OOLL DD
tthhee cceenntteerr ooff tthhee VVoolluummee
UUPP//DDOOWWNN bbuuttttoonn ((DDAABB11 KKeeyyppaadd))::
Mutes/un-Mutes all zones designated for PARTY MODE.
•• PP
RR EESS SS
tthhee ZZ
OONN EE
OOFFFF BBuuttttoonn::
Turns the local zone OFF.
•• PP
RR EESS SS
--AA
NN DD
--HH
OOLL DD
tthhee ZZ
OONN EE
OOFFFF BBuuttttoonn::
Turns all zones designated for PARTY MODE OFF.
•• PPrreessss bbuuttttoonnss 11 tthhrroouugghh 1122 ((DDAABB11 KKeeyyppaadd))::
Selects tuner presets 1 through 12.
•• PP
RR EESS SS
bbuuttttoonnss 11 tthhrroouugghh 00 ((CC44663300 SSEE NNuummeerriicc KKeeyyppaadd))::
Selects tuner presets 1 through 10.
•• PP
RR EESS SS
bbuuttttoonnss ““––”” aanndd ““++”” ((CC44663300 SSEE NNuummeerriicc KKeeyyppaadd))::
Selects tuner presets 11 and 12.
5) A R
EPEAT UNTIL BUTTON IS RELEASED command in the PRESS level will defeat the PRESS-AND-HOLD level for that button.
Building Macros
Individual keypad button macros are programmed in the
M
ACRO EDITOR window. To open MACRO EDITOR:
1. Open the D
EVICE screen (see
Figure 44,
opposite).
2. If the system has more than one DAB1, use the D
EVICE
SELECTOR
(see
Figure 41
) to select the one you want to
program. The Zone 1 programming screen for that
DAB1 will appear (see
Figure 45
).
• The Zone 1 programming screen will include one
set of V
OLUME UP/DOWN, MUTE and ZONE OFF
buttons and four sets of Z
ONE SOURCE CONTROL and
numeric buttons (one for each source). The source
names you selected on the S
OURCE SETUP screen (see
Figure 43
, on page 33) will appear on the four
S
OURCE buttons.
3. Right-click on the button you want to create or modify a
macro for.
• If the button already has been programmed with a
macro (a M
ACRO INDICATOR appears on the
button) select E
DIT MACRO.
• If the button has not been programmed with a macro (no M
ACRO INDICATOR appears on the button) select CREATE MACRO.
The M
ACRO EDITOR screen will appear. See
Figure 46
, on page 36.
Figure 45: Zone 1 Programming Screen
To Next Page
Loading...
