To Next PageTo Next Page
Need help?Do you have a question about the Sony CDX-2500R and is the answer not in the manual?
General| Power Output | 50W x 4 |
|---|---|
| Tuner Bands | FM/AM |
| RMS Power Output | 22W x 4 |
| CD Playback | Yes |
| CD-R/RW Playback | Yes |
| MP3 Playback | Yes |
| WMA Playback | Yes |
| Display Type | LCD |
| Removable Front Panel | Yes |
| Detachable Faceplate | Yes |
| Anti-Theft Protection | Yes |
| Bass Boost | Yes |
| Clock | Yes |
| Remote Control | Optional |
| Channels | 4 |
| Equalizer | 3-band |
| Preset Stations | 18 FM, 6 AM |
Resets the unit before first use or after battery replacement. Erases clock and some functions.
Explains how to remove the front panel to protect the unit from theft. Includes cautions.
Instructions for reattaching the front panel to the unit, with notes on proper alignment and care.
Details the audible alarm that sounds if the ignition is turned off without removing the front panel.
Instructions on how to insert a CD and start playback. Includes how to stop and eject.
Details how to cycle through display information like track number, elapsed time, and clock during playback.
Explains using the SEEK/AMS control to skip tracks forward or backward.
Guides on using SEEK/AMS control to search for a specific point within a track.
Explains repeat play, shuffle play, and other playback modes for CDs.
Describes using BTM to automatically store the strongest stations on each band.
Instructions for manually presetting up to 20 FM, 10 MW, and 10 LW stations.
How to select and listen to stations that have been preset using manual or automatic tuning.
Troubleshooting steps for when automatic or manual tuning fails to find a desired preset station.
Explains Radio Data System features like automatic retuning, traffic announcements, and programme type location.
How the station name appears in the display when an RDS station is received.
Instructions to switch to Monaural mode to improve sound quality when stereo reception is weak.
Details how to cycle through display information like frequency, station name, and clock.
Explains the AF function for automatically retuning to the strongest signal in a network for continuous listening.
How to use the REG-ON function to stay tuned to a regional programme without switching.
Allows selection of other local stations in the area, even if not stored on number buttons.
Explains how TA and TP data automatically tune into stations broadcasting traffic announcements.
Stores station data with frequency, allowing AF/TA settings to be applied automatically.
Instructions to set a uniform AF/TA function for all preset radio stations.
Guides on setting individual AF/TA functions for each preset radio station.
Instructions on how to attach the appropriate label to the optional rotary commander based on mounting position.
Explains how to operate the unit using the optional rotary commander's buttons and controls.
Guides on adjusting bass, treble, balance, and fader independently for each source.
How to use the ATT function on the rotary commander to temporarily lower the volume.
Instructions to reverse the control direction of the rotary commander for alternative mounting.
Details how to set items like clock display, beep sounds, rotary commander direction, and motion display.
How to adjust the bass level using the D-BASS control, with notes on distortion.
Important safety warnings regarding sunlight, power supply, speaker configuration, and power aerial.
Guidance on how to handle moisture condensation inside the CD player, affecting operation.
Warnings about using discs with sticky residue, old labels, or attached labels, which can damage the unit.
Instructions for safely replacing a blown fuse, including warnings about amperage ratings.
Steps to clean unit and front panel connectors to ensure proper function, with safety advice.
Solutions for common issues like no sound, erased memory, display errors, and no beep sound.
Troubleshooting steps for issues like disc loading, playback, ejection, and button malfunctions.
Solutions for preset tuning, automatic tuning, weak signals, noisy reception, and 'ST' indication.
Troubleshooting for SEEK start delays, no traffic announcements, and PTY display errors.
