CFD-RG880CP
7
Playable/Recordable USB devices
You can use the following Sony USB devices on this unit.
Other USB devices are not playable/recordable on this
unit.
Veried Sony digital music players (as of
September 2008)
Product name Model name Series name
Wa lk ma n
3
NWD- B100/B110F/
E020F
NWZ- A810/A820K/
B130F/E430F/
S510/S610F/
S630F/S710F/
S730F
Wa lk ma n
3
Phone W880i/W850/
W710/W660/
W580
W910
Check the websites below for the latest information
about compatible devices.
For customers in Europe:
<http://support.sony-europe.com/>
For customers in Latin America:
<http://www.sony-latin.com/pa/info>
For customers in Asia and Oceania:
<http://www.sony-asia.com/section/support>
Notes
[
When formatting the above models, be sure to format using the
modelitselforthe dedicatedformattingsowareforthatmodel.
[
Do not use any other than these USB devices. Operation of models
not listed here is not guaranteed.
[
Operation may not always be ensured even when using these USB
devices.
[
Some of these USB devices may not be available for purchase in
certain areas.
[
Playback of WMA/AAC les with copyright protection is not
supported.
[
Files downloaded from a music download website may not be
played.
[
Connection through a hub is not supported.
Connecting optional components
You can enjoy the sound from an optional component
such as a portable digital music player through the
speakers of this unit.
Be sure to turn o the power of each component before
making any connections.
For details, refer to the instruction manual of the
component to be connected.
Built-in audio cable
with stereo-mini plug
audio connecting
cable (not supplied)
or
(e.g.,portable digital
music player)
To AUDIO IN jack
To the line output jack
1 Connect the built-in audio cable with stereo-mini
plug
RT
on the unit to the line output jack of the
portable digital music player or other components*.
2 Turn the unit and the connected component on.
3 Press AUDIO IN
RH
on the unit and start playing
sound on the connected component.
e sound from the connected component is output
from the speakers.
* To connect the unit to a TV or VCR, use an extension cable (not
supplied) with a stereo-mini jack on one end (for the built-in audio
cable) and two phono plugs on the other end.
Recording the sound from the connected
component
1 Insert a blank tape.
2 Press AUDIO IN
RH
on the unit to display “AUDIO IN”.
3 Press
[
on the unit.
Recording starts.
4 Play the optional component connected to the unit.
Tip
Should the built-in audio cable
RT
become damaged, you can use the
AUDIO IN jack
RB
to connect an optional component to the unit.
Use an audio connecting cable (not supplied) with a stereo mini plug
on one end (for the AUDIO IN jack
RB
). Make sure the plug on the
other end is suited to the jack on the optional component; for
example, a stereo-mini plug for a portable digital music player, or two
phono plugs for a TV or VCR.
Notes
[
Do not pull forcibly on the built-in audio cable
RT
.Doingsomay
cause the plug to rip o.
[
Connect the built-in audio cable
RT
or audio connecting cable (not
supplied) securely to prevent any malfunction.
[
It is not possible to listen to two components connected at the same
time through the built-in audio cable
RT
and the AUDIO IN jack
RB
(using an optional audio connecting cable). Connect one
component at a time.
Presetting radio stations
You can store radio stations into the unit’s memory. You
can preset up to 30 radio stations, 20 for FM and 10 for
AM in any order.
1 Press RADIO/BAND
[
AUTO PRESET
on the unit to
select the band.
2 Hold down RADIO/BAND
[
AUTO PRESET
on the
unit for 2 seconds until “AUTO” ashes in the display.
3 Press DSPL/ENT
XG
on the unit.
e stations are stored in memory from the lower
frequencies to the higher ones.
If a station cannot be preset automatically
You need to preset a station with a weak signal manually.
1 Press RADIO/BAND
[
AUTO PRESET
on the unit to
select the band.
2 Tune in a station you want.
3 Hold down DSPL/ENT
XG
on the unit for 2 seconds
until the preset number ashes in the display.
4 Press PRESET + or –
on the unit until the preset
number you want for the station ashes in the
display.
5 Press DSPL/ENT
XG
on the unit.
e new station replaces the old one.
On the remote
1 Press RADIO/BAND
until the band you want
appears in the display.
2 Tune in a station you want.
3 Hold down ENTER
XM
for 2 seconds until the preset
number ashes in the display.
4 Press PRESET + or –
until the preset number you
want for the station ashes in the display.
5 Press ENTER
XM
.
Tip
e preset radio stations remain in memory even if you unplug the
AC power cord or remove the batteries.
Playing preset radio stations
1 Press RADIO/BAND
[
AUTO PRESET on the unit to
select the band.
2 Press PRESET + or –
on the unit to tune in the
stored station.
On the remote
1 Press RADIO/BAND
.
2 Press PRESET + or –
to tune in the stored station.
Falling asleep to music
1 Play the music source you want.
2 Press SLEEP
XE
to display “SLEEP”.
3 Press SLEEP
XE
to select the minutes until the unit
goes o automatically.
Each time you press the button, the indication
changes as follows:
“A U T O * ” U “60MIN” U “30MIN” U “20MIN” U
“10MIN” U “OFF”.
* When you select “AUTO”, the CD, USB or tape stops playing in
90 minutes at most and the unit goes o automatically. When
you are listening to the radio, the radio goes o in 90 minutes.
If 4 seconds have passed aer you pressed SLEEP
XE
,
the minutes in the display are entered.
When the setting becomes eective, the LCD
backlight will be dimmer and the Woofer LED will
turn o.
When the preset time has passed, the unit goes o
automatically.
To cancel the sleep function
Press POWER
to turn o the power.
Note
When you are playing a tape using this function:
If the tape length of one side is longer than the set time, the unit will
notgoo untilthetapereachesthe end.
To Next Page
Loading...
