EasyManua.ls Logo

Sony HCD-EP30 - SECTION 4 MECHANICAL ADJUSTMENTS; General Precautions for Mechanical Adjustments; Torque Measurement Procedures; Tape Tension Measurement Procedures

Sony HCD-EP30
38 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
11
HCD-EP30/EP40
SECTION 4
MECHANICAL ADJUSTMENTS
SECTION 5
ELECTRICAL ADJUSTMENTS
Tape Speed Adjustment
Setting:
Function: TAPE
Procedure:
1. Playback WS-48A (tape center) in the FWD state.
2. Adjsut the volume in CAPSTAN/REEL motor (M201) so that
the frequency counter reading becomes 3,000 Hz.
Specified Value: 2,985 to 3,015 Hz
3. Confirm that the frequency at the beginning and that at the
end of tape winding are between 2,955 to 3,045 Hz.
Adjustment Location:
PRECAUTION
1. Setting
MEGA BASS switch : OFF
TAPE DECK SECTION 0 dB=0.775 V
Test tape
Type Signal Used for
WS-48A 3 kHz, 0 dB Tape Speed Adjustment
P-4-A063 6.3 kHz, 10 dB Head Azimuth Adjustment
frequency counte
r
test tape
WS-48A
(3 kHz, 0 dB)
set
HEADPHONE board
PHONES jack (JK401)
+
32
CAPSTAN/REEL
motor (M201)
Tape Speed
Adjustment
Mode Tension Meter Meter Reading
FWD CQ-403A
more than 100 g
(more than 3.53 oz)
Tape Tension Measurement
PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened
swab :
record/playback head pinch roller
erase head rubber belts
capstan idlers
2. Demagnetize the record/playback head with a head demagne-
tizer. (Do not bring the head magnetizer close to the erase head.)
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
Mode Torque Meter Meter Reading
2.95 6.86 mNm
FWD CQ-102C (30 70 gcm)
(0.42 0.97 ozinch)
0.15 5.39 mNm
FWD
CQ-102C (1.5 5.5 gcm)
Back Tension
(0.021 0.076 ozinch)
more than 5.89 mNm
FF CQ-201B (more than 60 gcm)
(more than 0.83 ozinch)
more than 5.89 mNm
REW CQ-201B (more than 60 gcm)
(more than 0.83 ozinch)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

Related product manuals