• [Biuetooth Codec - AAC]
This
function
is
only
available
when
you set [Biuetooth Mode]
to
[Receiver]
or
[Transmitter].
[On]: Enable
AAC
codec.
[Off]: Disable
AAC
codec.
llmJ
You
can
enjoy high-quality sound
if
AAC
is
enabled and your device
supports
AAC.
If you cannot listen to
AAC
sound with your device, select
[Off].
• [Biuetooth Codec -
LDAC]
This
function
is
only
available when you set [Biuetooth Mode]
to
[Receiver]
or
[Transmitter].
[On]: Enable
LDAC
codec.
[Off]: Disable
LDAC
codec.
llmJ
You
can
enjoy more high-quality sound
if
LDAC
is
enabled
and
your
device supports
LDAC.
If you cannot listen to
LDAC
sound with your
device, select [Off].
• [Wireless Playback Quality]
You can set
the
transmission data rate
of
LDAC
playback. This
function
is
only
available
when
you set [Biuetooth
Mode]
to
[Transmitter] and [Biuetooth
Codec-
LDAC]
to
[On].
[Auto]: The data rate
is
automatically changed
depending
on
the
environment.
If
audio
playback
is
unstable in this mode, use the
other
three modes.
[Sound Quality]: The highest data rate
is
used. Sound
is
sent in a
higher
quality; however, audio playback sometimes
may
become
unstable
when
the
link
quality
is
not
good
enough.
[Standard]: The
middle
data rate
is
used. It balances
both
sound
quality
and playback stability.
[Connection]: Stability
is
prioritized. Sound
quality
may
be
reasonable and connection status will
most
likely be stable.
If
the
connection
is
unstable, this setting
is
recommended.
• [OSD Language]
You can select
the
language you
want
for
the
system on-screen
display.
• [Wireless Sound Connection]
You can make
further
settings
for
the
wireless system. For details,
see
II
Further Setting
for
the
Wireless System {Subwoofer)" (page 34).
• [IR-Repeater]
[On]: Remote signals
for
the
TV
are sent
from
the
rear
of
the Bar
Speaker (page 33).
[Off]: Turns
off
the
function.
• [HDMI Settings]
[Control
for
HDMI]
[On]: Turns on
the
[Control
for
HDMI] function. You can operate
mutually
between
device
that
are connected
with
an HDMI cable.
[Off]:
Off
[Audio Return Channel]
This
function
is
available
when
you connect
the
system
to
a TV's
HDMIIN jack
that
is
compatible
with
the
Audio
Return Channel
function
and [Control
for
HDMI]
is
set
to
[On].
[Auto]: The system can receive
the
digital audio signal
of
the
TV
automatically via
an
HDMI cable.
[Off]:
Off
[Standby Through]
You can
output
HDMI signals
to
the
TV
even
when
the
system
is
in
standby mode. This
function
is
available
when
you set [Control
for
HDMI]
to
[On].
[Auto]:
Outputs
signals
from
the HDMI
OUT
(ARC)
jack when
the
TV
is
turned
on
while
the system
is
in
the
standby mode. This setting
saves
power
in the standby
mode
compared
to
the
[On] setting.
[On]: Always
output
signals
from
the
HOM
I
OUT
(ARC)
jack
when
the
system
is
in standby mode.
If
you connect a
TV
other
than
liBRA
VIA,"
we recommend you
to
select this setting.
continued
---
2sus
To Next Page
Loading...
