Chapter
8
Color
Backgrounds,
Copy
and
Swap,
and
Other
Settings
The status area shows the setting status of each of the
following ports.
•
Switcher Remote S1 to Remote S2 ports (RS-422A,
D-sub 9-pin)
•
Switcher GPI port (parallel, 25-pin)
•
DME2 GPI port (parallel, 25-pin)
2 In the <Switcher> or <DME2> group, press the name
of the port for which you want to disable control from
an external device, turning it off.
To enable control for the port, press the name again.
Notes
For AUX bus operations from the Remote S1 to
Remote S2 ports of the switcher, the setting (Enable/
Disable/Manual) in the Setup menu takes precedence.
The settings made in the Port Enable menu only apply
when the setting is set to [Manual].
For details,
1
“Enabling or Disabling AUX Bus
Control” (p. 362).
DME override mode
1
Open the Misc >Enable >Port Enable menu (3211).
2
In the <DME Override> group, select the DME
override mode.
DME Override: When a switcher snapshot or effect
using a DME is recalled, forcibly select the DME
that was used when saving.
On Air Protect: The operation is the same as the
DME override function, except that a DME being
used by an M/E bank or PGM/PST bank that is on
air will not be forcibly selected.
Notes
•
If effects using the same DME channel are selected
simultaneously in two or more regions, the DME is
selected with the order of precedence P/P >M/E-1.
•
This function is disabled on the MVS-3000.
Enabling/disabling control from the
System Manager
You can perform some switcher data management and
control functions remotely by installing the BZPS-8000/
8000L system management software (System Manager)
on a networked computer.
1
Open the Misc >Enable >Port Enable menu (3211).
2
Press [System Manager].
The setting is enabled/disabled each time the button is
pressed.
Safe Title Settings
Turning the safe title function on/off
1
Open the Misc >Safe Title menu (3221).
2
Select the signal to set.
Notes
•
It is not possible to change the setting for the output
for which the safe title is set off in the Setup menu.
•
The safe title function cannot be used for output
signals for which through mode is set to Enable in a
Setup menu.
For details,
1
“Signal Output Settings” (p. 351).
3
Press [Safe Title], turning it on or off.
Displaying a List of Transition Rates
and Changing the Settings
In the Misc >Transition >Key/ME/FTB menu (3231), for
each bank you can display a list of the M/E (or PGM/PST)
transition rates and independent key (or DSK) transition
rates, and change the settings.
These settings are linked to the other transition rate setting
operations.
You can also display and set the fade-to-black transition
rate.
Menu display
The display of the independent key transition rate in the
Misc >Transition >Key/ME/FTB menu (3231) depends on
the selection in the <Key Transition> group of the
Engineering Setup >Switcher >Transition menu (7334) for
each of the switcher banks.
When [Same] (On direction and Off direction settings
are the same) is selected in the <Key Transition>
group: Only “Key” (or “DSK” in the PGM/PST bank)
appears.
When [Independ] (On direction and Off direction
settings are independent) is selected in the <Key
Transition> group: “Key(On)” and “Key(Off)” each
appear. In the PGM/PST bank, “DSK(On)” and
“DSK(Off)” appear.
For details,
1
“Settings Relating to Video Switching”
(p. 355).
To Next Page
Loading...
