Sony MDM-X4 Mk2 - Deleting a Tempo Map; MIDI Synchronization Using EXT; Connecting Multiple Units; Setup for External Sync

Synchronization with MIDI Equipment (Mk2)
Deleting a tempo map
Use the following operations to delete tempo maps
which are no longer necessarv. The tempo map
numbers located after the tempo map which was
deleted are brought forward automatically.
EXAMPLE: Erasing tempo map 5.
1 Press EDIT.
[EDIT] appears in the displav.
2 Tum the jog dial so that “Song Tempo” appears in
the display.
The name of the edit function starts blinking in
the display.
3 Press ENTER.
The tempo map setting display appears.
4 Turn the jog dial to display tempo map 05.
05:00184100
Blinking
5 Press ENTER.
The indication for the tempo change position
starts blinking.
Tempo map 1 can onlv be set to the first bar.
6 Turm the jog dial to the right to display Del.
05: DelJ100
Blinking
7 Press ENTER.
"Deleted"
appears
in
the
display
and
tempo
map
5 is deleted.
Gy
The
previous
operations
can
also
be
used
to
delete
tempo
map
1.
However,
tempo
map
1
should
only
be
deleted
after
deleting
all
the
other
tempo
maps
from
2
up.
ae RE
MIDI Synchronization Using
EXT
To connect several MDM-X4 M2 units, or sync this
unit with another MIDI component that cannot syne to
an external source, set this unit to external sync mode
and use the MTC (MIDI Time Code) from an external
source as the sync signal.
Connecting two MDM-X4
Use a MIDI cable to connect two MDM-X4 MK2, or an
MDM-\4 and an MDM-X4 Mk2 (in this case, be sure to
use the MDM-X4 Mk2 as the syne unit).
MDM-X4 Mk2
(or MDM-X4) MDM-X4 Mk2
Master unit Sync unit
. . °. .
°
c'e
2
e
MIDI MIDI
OUT IN
Ses
1
Mate co e ee eboe
MIDI signal
e
e
o
o
o
9
rj
o
E]
o
Do o0 6€ ee ve |,
mNINE)ocoeeee ce
(END © oo eee oboe
mn o Oc e efe e.
9
o
9
o
o
9
o
o
i
Do 000666 06
(WEN © COP eee 00
o ©
o ©
9 ©
oe
ee
o ©
a
35:
fi
Setup
1
Set
the
“Sync”
system
setting
of
the
master
unit
to
MTC.
See
“Changing
a
Setting”
(page
I8
of
the
main
"Operating
Instructions")
and
“Syne
mode
setting
(5vnc)"
(page
3
of
this
booklet)
for
details.
2
Set
the
“Syne”
system
setting
of
the
svnc
unit
to
ENT.
See
“Changing
a
Setting”
(page
18
of
the
main
“Operating
Instructions")
and
"Sync
mode
setting
(5vnc)"
(page
3
of
this
booklet)
for
details.
3
Set
both
units
to
the
beginning
of
the
appropriate
songs.
4 Start playback on the master unit.
The
syne
unit
starts
playing
in
syne
with
the
master unit. The signal is muted and “Chase”
appears in the display window until
synchronization stabilizes.
(continued)