Sony MDS-E12 - 3-5. Operating the Continuous Playback Mode; 1. Entering the Continuous Playback Mode; 2. Changing the Parts to Be Played Back; 3. Ending the Continuous Playback Mode

3-5-1.
Operating
the
Continuous
Playback
Mode
1.
Entering
the
continuous
playback
mode
1)
Set
the
disc
in
the
unit.
(Whichever
recordable
discs
or
discs
for
playback
only
are
available.)
2)
Turn
the
knob
and
display
“CPLAY
1
MODE”
(C34).
3)
Press
the
button
to
change
the
display
to
“CPLAY
1
MID”.
4)
When
access
completes,
the
display
changes
to
“C
=
SAD
SO.
Note:
The
numbers
“4?”
displayed
show
you
error
rates
and
“ADER”.
2.
Changing
the
parts
to
be
played
back
1)
Press
the
YES
button
during
continuous
playback
to
change
the
display
as
below.
The
parts
to
be
played
back
can
be
moved.
“CPLAY
1
MID”
—>
“CPLAY
1
OUT”
—
“CPLAY
1
el
2)
When
access
completes,
the
display
changes
to
“C
=
AD
=P’,
Note:
The
numbers
“i?”
displayed
show
you
error
rates
and
“ADER”.
3.
Ending
the
continuous
playback
mode
1)
Press
the
button.
The
display
will
change
to
“CPLAY
1
MODE”.
2)
Press
the
button
and
take
out
the
disc.
Note:
The
playback
start
addresses
for
IN,
MID,
and
OUT
are
as
follows.
IN
40h
cluster
MID
300h
cluster
OUT
700h
cluster
3-5-2.
Operating
the
Continuous
Recording
Mode
(Use
only
when
performing
self-recording/palyback
check.)
1.
Entering
the
continuous
recording
mode
1)
Set
a
recordable
disc
in
the
unit.
2)
Turn
the
[IK]
AMS
PPI]
knob
and
display
“CREC
1
MODE”
(C34).
3)
Press
the
[YES]
button
to
change
the
display
to
“CREC
1
MID”.
4)
When
access
completes,
the
display
changes
to
“CREC
1
CHEE?’
and
“
”
lights
up.
Note:
The
numbers
“1!”
displayed
shows
you
the
recording
position
addresses.
2. Changing the parts to be recorded :
1)
When
the
button
is
pressed
during
continuous
recording,
the
display
changes
as
below.
The
parts
to
be
recorded'can
be
changed.
" ” goes off during movement.
“CPLAY
1
MID”
—
“CPLAY
1
OUT”
—+
“CREC
1
IN”
2)
When
access
completes,
the
display
changes
to
“CREC
1
(£000"
and
“
”
lights
up.
Note:
The
numbers
“{!”
displayed
shows
you
the
recording
position
addresses.
3.
Ending
the
continuous
recording
mode
1)
Press
the
button.
The
display
changes
to
“CREC
1
MODE”
and
“
”
goes
off.
2)
Press
the
button
and
take
out
the
disc.
Note
1:
The
recording
start
addresses
for
IN,
MID,
and
OUT
are
as
follows.
IN
40h
cluster
MID
300h
cluster
OUT
_700h
cluster
Note
2:
The
[MENU/NO
]
button
can
be
used
to
stop
recording
anytime.
Note
3:
Do
not
perform
continuous
recording
for
long
periods
of
time
above
5
minutes.
Note
4:
During
continuous
recording,
be
careful
not
to
apply
vibration.
Sap ss