— 5 —
3-8. POWER BLOCK DIAGRAM (2/3) ······························3-15
3-9. POWER BLOCK DIAGRAM (3/3) ······························3-17
4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/3) ·······················4-1
FRAME SCHEMATIC DIAGRAM (2/3) ·······················4-3
FRAME SCHEMATIC DIAGRAM (3/3) ·······················4-5
4-2. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS ············································4-8
• CD-329 (CCD IMAGER)
PRINTED WIRING BOARD ·························4-9
• CD-329 (CCD IMAGER)
SCHEMATIC DIAGRAM ····························4-10
Shematic diagram and printed wiring board of the
VC-262 board are not shown.
Pages from 4-11 to 4-58 are not shown.
• LS-057 (S/T REEL SENSOR), FP-228 (DEW SENSOR),
FP-299 (MODE SWITCH), FP-300 (TAPE TOP),
FP-302 (TAPE END), FP-301 (TAPE LED)
FLEXIBLE BOARDS AND
SCHEMATIC DIAGRAM ····························4-59
• FP-332 (USB CONNECTOR), FP-270 (S VIDEO,
AUDIO/VIDEO), FP-272 (LANC, DV IN/OUT)
FLEXIBLE BOARDS AND
SCHEMATIC DIAGRAM ····························4-61
• MM-043 (MEMORY)
PRINTED WIRING BOARD ·······················4-63
• MM-043 (MEMORY)
SCHEMATIC DIAGRAM ····························4-65
• CF-084 (EVF DRIVE, USER FUNCTION)
PRINTED WIRING BOARD ·······················4-67
• CF-084 (USER FUNCTION)(1/2)
SCHEMATIC DIAGRAM ····························4-71
• FP-315 (VTR FUNCTION SWITCH),
FP-318 (FOCUS SWITCH)
SCHEMATIC DIAGRAM ····························4-72
• CF-084 (EVF DRIVE)(2/2)
SCHEMATIC DIAGRAM ····························4-73
• FP-315 (VTR FUNCTION SWITCH),
FP-318 (FOCUS SWITCH)
FLEXIBLE BOARDS···································4-75
• LB-071 (EVF BACK LIGHT)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ····························4-77
• FP-283 (PANEL REVERSE)
FLEXIBLE BOARD ·····································4-78
• SI-030 (STEADY SHOT, REMOTE COMMANDER
RECEIVER, LASER LINK)
PRINTED WIRING BOARD ·······················4-79
• SI-030 (STEADY SHOT, REMOTE COMMANDER
RECEIVER, LASER LINK)
SCHEMATIC DIAGRAM ····························4-81
• FP-273 (MIC, HEADPHONES)
FLEXIBLE BOARD AND
SCHEMATIC DIAGRAM ····························4-81
• PD-138 (RGB DRIVE, TIMING GENERATOR, LCD
DRIVE, BACK LIGHT DRIVE)
PRINTED WIRING BOARD
(DCR-TRV730) ·
4-83
• PD-138 (RGB DRIVE, TIMING GENERATOR)(1/2)
SCHEMATIC DIAGRAM ····························4-85
• FP-283 (PANEL REVERSE)
SCHEMATIC DIAGRAM ····························4-85
• PD-138 (LCD DRIVE, BACK LIGHT DRIVE)(2/2)
SCHEMATIC DIAGRAM ····························4-87
• PD-139 (RGB DRIVE, TIMING GENERATOR, LCD
DRIVE, BACK LIGHT DRIVE)
PRINTED WIRING BOARD
(DCR-TRV725E/TRV730E/TRV828/TRV828E/
TRV830/TRV830E) ······································4-89
• PD-139 (RGB DRIVE, TIMING GENERATOR)(1/2)
SCHEMATIC DIAGRAM ····························4-91
• FP-283 (PANEL REVERSE)
SCHEMATIC DIAGRAM ····························4-91
• PD-139 (LCD DRIVE, BACK LIGHT DRIVE)(2/2)
SCHEMATIC DIAGRAM ····························4-93
• FU-155 (POWER SUPPLY)
PRINTED WIRING BOARD ·······················4-95
• FU-155 (POWER SUPPLY)
SCHEMATIC DIAGRAM ····························4-97
4-3. WAVEFORMS ······························································4-99
Waveforms and parts location of the VC-262 board
are not shown.
Pages from 4-101 to 4-104 are not shown.
4-4. MOUNTED PARTS LOCATION ·······························4-105
5. ADJUSTMENTS
1. Before starting adjustment···············································5-2
1-1. Adjusting items when replacing main parts and boards. ·5-2
5-1. CAMERA SECTION ADJUSTMENT ···························5-4
1-1. PREPARATIONS BEFORE ADJUSTMENT
(CAMERA SECTION) ···················································5-4
1-1-1.List of Service Tools························································5-4
1-1-2.Preparations ·····································································5-5
1-1-3.Precaution ········································································5-7
1. Setting the Switch····························································5-7
2. Order of Adjustments ······················································5-7
3. Subjects ···········································································5-7
1-2. INITIALIZATION OF A, B, C, D, E, F, 4, 9, 7, 8 PAGE
DATA ···············································································5-8
1-2-1.INITIALIZATION OF C, D, 8 PAGE DATA ··················5-8
1. Initializing the C, D, 8 Page Data····································5-8
2. Modification of C, D, 8 Page Data ··································5-8
3. C Page Table ····································································5-8
4. D Page Table····································································5-9
5. 8 Page Table···································································5-10
1-2-2.INITIALIZATION OF B PAGE DATA ·························5-11
1. Initializing the B Page Data···········································5-11
2. Modification of B Page Data ·········································5-11
3. B Page Table ··································································5-11
1-2-3.INITIALIZATION OF E, F, 7 PAGE DATA ·················5-12
1. Initializing the E, F, 7 Page Data ···································5-12
2. Modification of E, F, 7 Page Data ·································5-12
3. F Page Table ··································································5-12
4. E Page Table ··································································5-13
5. 7 Page Table···································································5-13
1-2-4.INITIALIZATION OF A, 4, 9 PAGE DATA·················5-14
1. Initializing the A, 4, 9 Page Data···································5-14
2. Modification of A, 4, 9, Page Data ································5-14
3. A Page Table··································································5-14
4. 4 Page Table···································································5-15
5. 9 Page Table···································································5-16
1-3. CAMERA SYSTEM ADJUSTMENTS ························5-17
1. HALL Adjustment ·························································5-17
2. Flange Back Adjustment (Using Minipattern Box) ·······5-18
3. Flange Back Adjustment
(Using Flange Back Adjustment Chart and Subject
More Than 500m Away) ···············································5-19
3-1. Flange Back Adjustment (1) ··········································5-19
3-2. Flange Back Adjustment (2) ··········································5-19
To Next Page
Loading...
