EasyManua.ls Logo

Soundoff Signal 380 SERIES - User Manual

Soundoff Signal 380 SERIES
6 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website at www.soundoffsignal.com and select the “Warranty & Returns”
link along the left column of our home page. If you have questions regarding this product please contact Technical Services, Monday - Friday, 8 am to 5 pm at 1.800.338.7337, press #4 to
skip the automated message. Questions or comments that do not require immediate attention may be emailed to techsupport@soundoffsignal.com.
1.800.338.7337. / www.soundoffsignal.com / Thank you for trusting us with your safety!
Effective sirens generate loud sound
pressure levels that can potentially cause
hearing damage. Installers and those around
the vehicle need to be aware of the dangers
and wear hearing protection whenever the
siren system is operating. Vehicle operators
and occupants should assess their exposure
to siren noise and determine what steps
need to be taken to prevent hearing damage.
The siren system is intended for use by
authorized personnel only. It is the user’s
responsibility to ensure they understand and
operate the emergency warning devices in
compliance with all applicable city, state,
and federal laws and regulations. SoundOff
Signal assumes no liability for any loss
resulting from the use of the siren system.
Package Contents:
1 ea. Amplifier Box
1 ea. Microphone Bracket w/ Mounting
Hardware
4 ea. Amplifier Wire Harnesses with
Connectors (1-4 pin, 1-12 pin, 1-5 pin
and 1-14 pin)
1 ea. Instruction Manual
1 ea. Operators Warning Card to remain in
vehicle for operator review
1 ea. Sound Pressure Warning Label that is
to be attached in vehicle and in plain
site of operator and occupants of the
vehicle
1 ea. Mounting Bracket with Hardware
1 ea. Label Card for Aux. Switches
Wire capacity requirements for siren
amplifier (incoming power)-each supply and
ground wire.
0-10 Feet: 14 AWG
10-20 Feet: 12 AWG
20-30 Feet: 10 AWG
30+ Feet: Consult Factory to determine
requirements
380 SERIES REMOTE SIREN
ETSA380R
Please see back page for
Technical Specifications
ETSA380R 4.12
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
Important Information:
IMPORTANT NOTICE TO INSTALLER:
Make sure to read and understand all
instructions and warnings before proceeding
with the installation of this product. Ensure
the manual and all warning cards are
delivered to the end user of this equipment.
Introduction
The ETSA380R is Remote Mounted Siren
Amplifier designed for dual 100 Watt
speaker use. The siren comes standard with
a noise-cancelling microphone for PA use.
The amplifier box contains a dual amplifier
capable of supplying sound to dual 100 Watt
speakers. The ETSA380R also includes a 3
position slide switch and 8 independently
controlled accessory switches each capable
of supplying 10-20 amps.
The primary operating modes are User
Selectable tone, Yelp, Wail, Radio, PA,
Horn Override, and a push-button Manual
Override are available in all modes. All
tones except Wail and Yelp for California
Title 13 compliance may be disabled by
programming the siren.
Sirens provide an essential function of an
effective audio / visual warning system.
However, sirens are only short range
secondary devices. The use of a siren does
not insure that all drivers can or will abide
by or react to an emergency warning signal,
especially at high rates of speeds or long
distances. The operator of the vehicle must
never take the right of way for granted and
it is the operator’s responsibility to proceed
safely.
The effectiveness of this siren system is
highly dependant on the correct mounting
and wiring. The installer must read and
follow the manufacturer’s installation
instructions and warnings in the manual.
The vehicle operator should verify the siren
system is securely fastened to the vehicle
and properly functioning.
!
WARNING
Sirens produce loud sounds that
may damage hearing:
- Roll up windows.
- Wear hearing protection.
- Use only for emergency response.
- Avoid exposure to siren sound
outside of vehicle.
Control Panel (Universal Bail Bracket
included - not shown)
Amplifier
Microphone
Question and Answer IconNeed help?

Do you have a question about the Soundoff Signal 380 SERIES and is the answer not in the manual?

Soundoff Signal 380 SERIES Specifications

General IconGeneral
BrandSoundoff Signal
Model380 SERIES
CategorySecurity System
LanguageEnglish

Summary

Important Notice to Installer

Introduction

Overview of the ETSA380R remote mounted siren amplifier for dual 100 Watt speaker use.

Package Contents

Lists all items included in the ETSA380R siren amplifier package.

Important Information

Programming Modes

Auxiliary Switch Settings

Instructions for programming auxiliary switch functions and LED indicators.

Slide Switch Settings

Procedure for configuring slide switch settings for various functions.

Input Settings

Configuration options for input signals like Park Kill and Horn Ring.

Default Settings

Details the factory default configurations for buttons and switches.

Other Modes

Horn Ring Standby Tone

Sets the tone output for the horn ring when the siren is in standby.

8 Second Level; Aux Switch Buzzer Alert

Configures the 8-second timer and buzzer alert for auxiliary switches.

Air Horn Button Output Channels

Defines how the air horn button tone is output on speakers.

Alternate Modes

Alternate Horn Ring Control

Enables or disables alternate control for the horn ring function.

Alternate Horn Ring Control Option

Selects the option for alternate horn ring control when disabled.

Gun Lock Security

Configures the gun lock security feature for the siren system.

Setting PA Volume

Tone Programming

Yelp Button Tones

Maps Yelp button presses to specific speaker outputs and tone types.

Horn Button Tones

Maps Horn button presses to specific speaker outputs and tone types.

Tone Button Mapping

Configures which specific tones are activated by the tone button.

Manual Button Tones

Maps Manual button presses to specific speaker outputs and tone types.

Wail Button Tones

Maps Wail button presses to specific speaker outputs and tone types.

Auxiliary Button to Slide Switch Mapping

LED Indicators

Auxiliary and Slide Switch LED Indicators

Defines the conditions for Auxiliary and Slide Switch LED indicators.

Siren Amplifier Diagnostic Indicators

Explains the conditions indicated by the Siren Amplifier diagnostic LEDs.

Technical Specifications

Replacement Parts & Accessories

Related product manuals