EasyManua.ls Logo

SPT WA-1400E - User Manual

SPT WA-1400E
20 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Model No. WA-1400E Model No. WA-1410E
Model No. WA-1400H Model No. WA-1410H
ʳ
It is important that you read these
instructions before using your new
purchase and we strongly
recommend that you keep them in a
safe place for future reference.
Instruction Manual
P O R T A B L E
Air Conditioner
05-03-457 A029-OK.PDF
Sales: 800-934-9194

Questions and Answers

  • L
    Laura RussellJul 30, 2025
    Why is my room not cold enough with SPT Air Conditioner?
    • S
      smithandreaJul 30, 2025
      The room being cooled by the SPT Air Conditioner should have proper insulation. Ideal cooling may not be achieved if the unit is used in un-insulated rooms, such as sunrooms, garages, or attics.
  • J
    jacksonvanessaAug 4, 2025
    Why does my SPT Air Conditioner seems to do little?
    • J
      Joshua FrederickAug 4, 2025
      If the SPT Air Conditioner seems to be doing little, consider these factors: * Are curtains and blinds drawn to block direct sunlight? * Are there too many open windows or doors? * Are there too many people in the room? * Is there a heat-producing source in the room?
  • T
    Tara MoranAug 9, 2025
    What to do if my SPT WA-1400E seems to do nothing?
    • H
      Hannah WilliamsAug 9, 2025
      If your SPT Air Conditioner seems to be doing nothing, consider the following: * Check if the dust filter is dirty. * Inspect the air intake and outlet for any dirt or blockages. * Ensure the room temperature is not below the set temperature on the unit.
  • S
    sean73Aug 13, 2025
    What to do if the compressor doesn’t run on my SPT Air Conditioner?
    • A
      aaron22Aug 14, 2025
      If your SPT Air Conditioner's compressor isn’t running, it could be due to a few reasons: 1. The overheat protection feature on the compressor might be active. Wait for the unit's temperature to decrease. 2. The water tank could be full and in need of draining. 3. The settings might have been recently changed. Allow approximately 3 minutes for the compressor to restart.
  • T
    Tracy MilesAug 19, 2025
    How to troubleshoot SPT WA-1400E Air Conditioner that doesn’t run or only runs in fan mode?
    • D
      Darren MoodyAug 19, 2025
      If your SPT Air Conditioner isn't running or only operates in fan mode, check the following: * Ensure the unit is properly plugged in. * Verify the main power supply is switched on. * Confirm the room temperature is within the appliance's operational range. * If the unit is in Auto mode, switch to Cool or Heat and adjust to the desired temperature.
  • L
    Leah MortonAug 25, 2025
    Why is my SPT WA-1400E too noisy?
    • A
      Alexandria MosleyAug 26, 2025
      If your SPT Air Conditioner is too noisy, make sure that: * The unit is positioned evenly to prevent vibration. * The unit is placed on stable and even ground.

Summary

Before Use Instructions

Installation Guide

Exhaust Pipe Mounting

Operation Basics

Turning Unit On;Off and Mode Selection

Instructions on powering the unit, its default modes, and how to select desired operating modes like Cool or Heat.

Temperature Settings and Modes

Setting Cooling and Heating Temperatures

Guides on manually setting desired temperatures for cooling and heating modes, including operational notes.

Operational Notices and Airflow

Important Operational Notes

Key information regarding compressor start-up delays, temperature differentials, and anti-frost function.

Drainage Procedures

Draining into a Container

Step-by-step guide for emptying the water tank into a container using the provided tray.

Heating Function Cautions

Maintenance and Storage

Cleaning the Unit and Filters

Instructions for cleaning the housing and filters, including important notices about filter usage.

Troubleshooting Common Issues

Common Issues and Solutions

A list of common problems, their potential causes, and recommended solutions for the air conditioner.

Warranty Information

Safety and Power Cord

LCDI Plug Testing and Safety

Instructions for testing the Leakage Current Detection and Interruption (LCDI) plug and safety precautions for the power cord.

SPT WA-1400E Specifications

General IconGeneral
Voltage115V
Fan Speeds3
Digital ThermostatYes
Remote ControlYes
Auto RestartYes
24-Hour TimerYes
Operating Temperature62°F - 90°F
TypeWindow
Cooling Capacity14000 BTU
Coverage Area700 sq ft
Window KitYes

Related product manuals