Stanley Fatmax SFMCCS630 User Manual

7
ENGLISH
of the bar, and push backward when cutting along the top
edge of thebar.
2 . Do not overreach.
3 . Keep proper footing and balance at alltimes.
4 . Don’t let the nose of the guide bar contact a log, branch,
ground or otherobstruction.
5 . Don’t cut above shoulderheight.
6 . Use devices such as low kickback chain and reduced
kickback guide bars that reduce the risks associated
withkickback.
7 . Only use replacement bars and chains specified by the
manufacturer or theequivalent.
8 . Never let the moving chain contact any object at the tip
of the guidebar.
9 . Keep the working area free from obstructions such
as other trees, branches, rocks, fences, stumps, etc.
Eliminate or avoid any obstruction that your saw chain could
hit while you are cutting through a particular log orbranch.
10 . Keep your saw chain sharp and properly tensioned. A
loose or dull chain can increase the chance of kickback.
Check tension at regular intervals with the motor stopped and
tool unplugged, never with the motorrunning.
11 . Begin and continue cutting only with the chain moving
at full speed. If the chain is moving at a slower speed, there is
a greater chance for kickback tooccur.
12 . Cut one log at atime.
13 . Use extreme caution when re‑entering a previous cut.
Engage bucking spikes into wood and allow chain to reach full
speed before proceeding withcut.
14 . Do not attempt plunge cuts or borecuts.
15 . Watch for shifting logs or other forces that could close a
cut and pinch or fall intochain.
Kickback Safety Features

WARNING: The following features are included on your
saw to help reduce the hazard of kickback; however such
features will not totally eliminate this dangerous reaction.
As a chain saw user do not rely only on safety devices.
You must follow all safety precautions, instructions, and
maintenance in this manual to help avoid kickback and
other forces which can result in seriousinjury.
• Reduced‑Kickback Guide Bar, designed with a small radius
tip which reduces the size of the kickback danger zone on
bar tip. A reduced ‑ kickback guide bar is one which has
been demonstrated to significantly reduce the number and
seriousness of kickbacks when tested in accordance with safety
requirements for electric chainsaws.
• Low‑Kickback Chain, designed with a contoured depth gauge
and guard link which deflect kickback force and allow wood to
gradually ride into the cutter. A low‑kickback chain is a chain
which has met kickback performance requirements of ANSI
B175.1–2012.
• Do not operate chain saw while in a tree, on a ladder, on a
scaffold, or from any unstablesurface.
k ) Cut wood only. Do not use chain saw for purposes
not intended. For example: do not use chain saw for
cutting metal, plastic, masonry or non‑wood building
materials. Use of the chain saw for operations different
than intended could result in a hazardous situation.
l ) Do not attempt to fell a tree until you have an
understanding of the risks and how to avoid them.
Serious injury could occur to the operator or bystanders
while felling a tree.
m ) Follow all instructions when clearing jammed
material, storing or servicing the chain saw.
Make sure the switch is off and the battery pack is
removed. Unexpected actuation of the chain saw while
clearing jammed material or servicing may result in
serious personal injury.
Causes and operator prevention of kickback:
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinches the
saw chain in the cut.
Tip contact in some cases may cause a sudden reverse reaction,
kicking the guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide bar may push
the guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of the saw
which could result in serious personal injury. Do not rely exclusively
upon the safety devices built into your saw. As a chain saw user,
you should take several steps to keep your cutting jobs free from
accident or injury.
Kickback is the result of chain saw misuse and/or incorrect
operating procedures or conditions and can be avoided by taking
proper precautions as given below:
a ) Maintain a firm grip, with thumbs and fingers
encircling the chain saw handles, with both hands
on the saw and position your body and arm to allow
you to resist kickback forces. Kickback forces can be
controlled by the operator, if proper precautions are
taken. Do not let go of the chain saw.
b ) Do not overreach and do not cut above shoulder height.
This helps prevent unintended tip contact and enables better
control of the chain saw in unexpected situations.
c ) Only use replacement guide bars and saw chains
specified by the manufacturer. Incorrect replacement
guide bars and saw chains may cause chain breakage
and/or kickback.
d ) Follow the manufacturer’s sharpening and
maintenance instructions for the saw chain. Decreasing
the depth gauge height can lead to increased kickback.
The Following Precautions Should Be
Followed to Minimize Kickback:
1 . Grip saw firmly. Hold the chain saw firmly with both
hands when the motor is running. Use a firm grip with
thumbs and fingers encircling the chain saw handles.
Chain saw will pull forward when cutting on the bottom edge

Stanley Fatmax SFMCCS630 Specifications

General

Brand	Stanley
Model	Fatmax SFMCCS630
Category	Chainsaw
Language	English