Stanley SXPW17E User Manual (English)

Questions and Answers:

M
Michelle WeaverAug 4, 2025
Why Stanley SXPW17E pump does not reach working pressure?
- J
  Joshua MooreAug 4, 2025
  The Stanley Pressure Washer pump might not be reaching working pressure due to several reasons. It could be a worn nozzle, which would require replacement. The water filter might be dirty and needs cleaning. Ensure the water supply tap is fully open to provide sufficient water. Air being sucked into the system or trapped in the pump can also cause this issue; check the tightness of hose fittings and try depressing/releasing the gun trigger until the water flow is steady. Also, verify the adjustable nozzle is correctly positioned and the suction height is not more than 0.5 m. In some cases, the thermostatic valve may have tripped, requiring you to wait for the correct water temperature to be restored.
N
Nichole CoxAug 8, 2025
What to do if Stanley SXPW17E Pressure Washer motor 'buzzes' but fails to start?
- M
  Miss Diane HoltAug 8, 2025
  If the Stanley Pressure Washer motor buzzes but doesn't start, the power supply voltage may be too low. Check that the voltage of the mains power supply line is the same as indicated on the appliance's plate. Also, a voltage drop might occur due to the use of an extension cable; verify the characteristics of the extension cable.
V
vwelchAug 13, 2025
What to do if Stanley SXPW17E Pressure Washer pump pressure drops during sudden use?
- J
  Jennifer ChapmanAug 13, 2025
  If the Stanley Pressure Washer's pump pressure drops suddenly, it could be because water is being drawn from an external tank; try connecting the appliance to the mains water supply. The inlet water might be too hot, so reduce the temperature. Additionally, the nozzle or inlet filter may be clogged, requiring you to clean them.
S
shaunthomasAug 17, 2025
How to fix Stanley Pressure Washer motor that fails to start?
- J
  James LewisAug 17, 2025
  If the Stanley Pressure Washer motor fails to start, first check that the plug is firmly in the socket and that the mains voltage supply is present. If the issue persists and your model has this feature, use the tool to unjam the motor through the hole at the rear of the appliance.
M
morganlawrenceAug 22, 2025
Why Stanley Pressure Washer has no detergent sucked in?
- K
  Kimberly GalvanAug 22, 2025
  If the Stanley Pressure Washer is not sucking in detergent, make sure the adjustable nozzle is not on the high-pressure setting; set it to the appropriate setting. The detergent might be too dense, so dilute it with water. If you're using a high-pressure hose extension, fit the original hose instead.
M
Michelle JacksonAug 26, 2025
Stanley Pressure Washer (TSS versions only) no water delivery when gun trigger is depressed, what to do?
- C
  Curtis MurphyAug 26, 2025
  If there is no water delivery when the gun trigger is depressed on your Stanley Pressure Washer (TSS versions only), the nozzle might be clogged. Clean the nozzle.
C
Christopher SmithAug 30, 2025
Why water escapes from thermostat valve of Stanley Pressure Washer?
- D
  Doris WatsonAug 30, 2025
  Water may escape from the thermostat valve of your Stanley Pressure Washer if the water temperature inside the pump head has exceeded the maximum rated value stated on the nameplate. To prevent this, with the appliance in operation, do not stop the water jet for more than 5 minutes at a time.

Stanley SXPW17E Specifications

General

Power	1700 W
Max Pressure	130 bar
Flow Rate	420 L/h
Weight	7.3 kg
Hose Length	6 m
Cable Length	5 m
Voltage	230 V
Power Source	Electric
Maximum Pressure	130 bar
Water Flow	420 L/h
Nozzles Included	Yes